Jump to content
SAU Community

Group Buy : Motul 300v 10w40 (victoria Only)


Recommended Posts

MOTUL 300V 10w40 $89 for 4 L rrp $109 i will need about 15 people for this to go ahead no money up front will be needed

just leave your name if your 100% interested at the end of it i will get stock sent to

STATUS TUNING

63 Rodeo Drive

South Dandenong

Phone: (03) 9792 3333

Fax: (03) 9792 5555

E-Mail: [email protected]

OPEN 9.30am - 6.30pm Monday to Friday

(victoria) and can be paided and picked up from there

i will leave this up for 1 month from the 27/01/09 - 27/02/09

stock is coming from link international in Queensland

cheers

300V CHRONO

10W40

New 300V series is racing lubricant for racing cars.

MOTUL has developed “Double Ester Technology” for new 300V series, superior to complex ester that recognized the best base oil for engine oil up to now. Double Ester Technology, made by carefully balancing the ratio of complex ester and the newly developed macromolecular high polymer ester, enable base oil more wide-ranged, and delivers high output performance and superior reliability.

Also by carefully selecting the right polymer, “0% shear loss*” can be achieved.

*Diesel Injector method (CEC L-14-A-93), a standardized testing procedure for a lubricant’s shearing force.

Can be mixed with another viscosity of same series to achieve most suitable viscosity for the engine. (except for 5W-40)

* All-round use, designed for handling stable oil pressure preservation and sharp response.

* Compatible with a wide selection of engines — naturally aspirated, high torque turbo and cars that produce average to high levels of exhaust fumes.

SPECIFICATIONS

Product 300V CHRONO

Feature 100% Synthetic, Double Ester Technology, 0% Shear loss, can mix, for cars only.

SAE/DOT Standard 10W40

Specification Exceeds all existing standards

Maker's Approval —

Compatibility For a wide selection of engines — naturally aspirated, high torque turbo and cars that produce average to high levels of exhaust fumes

post-6642-1232982378_thumb.jpg

Why is it that motul dont make any of the 300V in 5L's? I asked the link rep last time he was up in our store and he didn't really know. Is there a reason for it? Always wondered about this.

  • 3 weeks later...
  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...