Jump to content
SAU Community

Recommended Posts

i have a mate aswell who has a u12 like me and he wanted to know if a ka24de is a east west motor and will it fit in a u12?

KA24DE was used in locally sold U13 Bluebird and is definitely east-west (FWD). I had to fix one recently that had blown the distributor (common problem due to oil seal leak stuffing the internal electronics). Nissan wanted extortionate $$ even at trade prices and I ended up getting one in from the US at a fraction of the price along with all the rocker cover gaskets.

Anyway, the locally sold U12 Pintara came with the CA20E engine (read: boat anchor) as well as the KA24E (single cam) engine in higher spec models (Ti hatch). I'd say dropping in a KA24DE would be a relatively simple swap, but I've never done it so can't say for sure.

mate has a pintara TRX with the ka24E. lump of shite motor, and id say the twin cam version would be only slightly better. In japan the released the same car with 4wd and SR20det power....

think about it :down:

im sure u can get a different sump to suit a rwd application.

OP was asking about FWD application for a U12. U13 Bluebird fits the bill.

KA24DE was certainly available in RWD version. For example, late 90's Navara in Australia (actually both RWD and 4WD versions). In the US there was the popular 240SX (S13 and S14), of course, and even though Nissan never offered a turbo version from the factory, there have been many successful aftermarket turbo kits made for the KA24DE (designated KA24DE-T).

nissan usa released 240sx that had the ka24 rwd (180sx here) pintara in aus has the ka24, not that bad for what they are, would rather an sr20det though as jap u13 bluebird is (sss blubird if you see one look for the sss on the side, means sr20det 4wd inside)

  • 7 months later...
KA24DE was used in locally sold U13 Bluebird and is definitely east-west (FWD). I had to fix one recently that had blown the distributor (common problem due to oil seal leak stuffing the internal electronics). Nissan wanted extortionate $$ even at trade prices and I ended up getting one in from the US at a fraction of the price along with all the rocker cover gaskets.

Anyway, the locally sold U12 Pintara came with the CA20E engine (read: boat anchor) as well as the KA24E (single cam) engine in higher spec models (Ti hatch). I'd say dropping in a KA24DE would be a relatively simple swap, but I've never done it so can't say for sure.

Hello, I tried to PM you but I can't till my post count is at least 10. Was just wanting to know where you got the dizzy for the U13 KA24de motor from? I'm chasing one and retail is $575 at repco, and only a little less than that for trade price. Auto elecs want 300-400 to replace the module. What symptoms does the car get when the dizzy stuffs up? On this one, it has the oil leak as you mentioned, and it sometimes starts then shuts off after a minute, then won't start, and sometimes feels as though it's delivering weak spark.

Looking forward to your reply.

Thanks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...