Jump to content
SAU Community

Recommended Posts

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

hey pplz wrecking my 32 GTR car is complete so anything not listed here ive deffinately got but heres the main things.

Blitz SBC - 300

Recaro drivers seat with rail 500

Guards 250 each

bonnet 550

Front bar with lower lip (lower liphas a few chips nuffn major) has nI slots 700

Front bar reinforcing 250

R34 GTR N1 turbos part # 707160-7 minimal shaft pay 1200(pair)

R34 GTR front lower control arms - 300 each

GTR grille- 250

GTR indicators- 150 each

GTR passenger seat - 350

Exhaust control valve- 200

Apexi Stainless steel 3 inch catback exhaust- 700

GTR push type Gearbox- 900

Cylinder head minus cams, cam covers 900

As stated before im wrecking the whole car so if u need anything i havent listed pm me and il get bakc to u asap with a price

All parts located in melb but can send at buyers expense

Hey Mate,

Interested in the 3inch Apexi exhaust, is it still available?

Cheers

Nick

Edited by HELLSCREAM R32 GTR

tried sending a pm but your inbox is full,

i need the whole boot interior, including plastics around the lights,

ash tray, and kick panels,

original airbox if you have it.

and i think thats it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...