Jump to content
SAU Community

Recommended Posts

hey folks

round three is being tomorow for me with my graphics :banana: cant wait...........not telling anyone what they are about ull just have to what and see........

im hoping to get to melbourne autosalon this year..... and adelaide of course still :)

here is a reminder of what has been previously done to the car:

DSCF4518-1.jpg

DSCF2960.jpg

2007_0812satautosalon20174.jpg

just thought i would share lol my show season starts this sunday ;)

Link to comment
https://www.sau.com.au/forums/topic/255456-round-iii/
Share on other sites

ok guys i think i might show her off a more now lol the quality of the pics might not be the best but it shows off the final product of the front of the car then on sunday night after the show ill get some nice ones up.......the only thing missing from the design is the roof part...........that will be done in a couple of weeks time when it cools down as the glue used really dosent like 40 degree heat which we have been having in adelaide.

i promise to get some killa pics on sunday...........did i mentions i got a custom boot install too?? :)

post-36647-1233922225_thumb.jpg

post-36647-1233922295_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/255456-round-iii/#findComment-4412627
Share on other sites

Those plates belong on a VL or a silvia :geek: .

Interesting graphics, are you part of the company that does the vinyls or know someone there?

The vinyl would have been printed onto instead of using the old method of using layered vinyls hey? If so it would have cost a mint to do those vinyls if they're printed.

Curious, but when they do judging, do they compare vinyls with airbrushing or are they two separate categories?

P.S. I'm still keen to see your dyno graph.

Link to comment
https://www.sau.com.au/forums/topic/255456-round-iii/#findComment-4414523
Share on other sites

Those plates belong on a VL or a silvia :geek: .

Interesting graphics, are you part of the company that does the vinyls or know someone there?

The vinyl would have been printed onto instead of using the old method of using layered vinyls hey? If so it would have cost a mint to do those vinyls if they're printed.

Curious, but when they do judging, do they compare vinyls with airbrushing or are they two separate categories?

P.S. I'm still keen to see your dyno graph.

haha i have these plates on the car since i got her.........

nah not part of the company just sponsored by them....they have done the graphics for the 34 since the start back in 2007........... and yes they are printed.....

and each show is different when it comes to judging....

more pics...

SMASA results: 3rd Top Import Class :)

post-36647-1234084496_thumb.jpg

post-36647-1234084741_thumb.jpg

post-36647-1234085046_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/255456-round-iii/#findComment-4414860
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...