Jump to content
SAU Community

Recommended Posts

Look Raegan, no one is denying your setup is tough, you have the quickest car in your class in your country and you do it all yourself which is friggin awesome. Its a great credit to you and whoever helped you.

What happened in Chille? post up pics!!! post up dyno sheet as well

and as for you floggin my car... Everyone talked it up and said that to me has learnt the hard way.. besides i am over drag racing i don't even think i will drag race it again.

You're just skeeeered of him aint ya guilt. ;)

  • Replies 136
  • Created
  • Last Reply

Top Posters In This Topic

You're just skeeeered of him aint ya guilt. ;)

He lives in Peru.. we could argue about who's car is faster untill the letters wear off on our keyboards! I aint going to be able to race him to find out who is quicker so I aint really interested in the arguement. However he has already beaten my best et.. so unless i go back and finally run a 10 he is faster then me anyway.

He lives in Peru.. we could argue about who's car is faster untill the letters wear off on our keyboards! I aint going to be able to race him to find out who is quicker so I aint really interested in the arguement. However he has already beaten my best et.. so unless i go back and finally run a 10 he is faster then me anyway.

I guess what happens in peru stays in peru.

I guess what happens in peru stays in peru.

apparently he went to chille to race some gtr's etc etc.. he wont tell us how he went!

How did you go in Chille ? its okay if the GTR's flogged you. they are a car of their own anyway.. would be like me racing the Dirt man.

Did the stock bottom end let go in chile?

lol.. its far from stock. i remember he put it together without giving the block a light skim.. seems to be holding up good though ;)

1992 msdos dyno readout ftw :)

jokes, well done mate!!! like other have said, around 370-380rwkw would be a more realisitc measure for that mph

that was an old trap with an old tune at lower boost and lower timing 3 degrees of timing nad 2 psi of boost

that was an old trap with an old tune at lower boost and lower timing 3 degrees of timing nad 2 psi of boost

When when are you re-running it ? and .....

WHAT HAPPENED IN CHILLE?!?

it actually checks out...my car running in HPI a while ago (Garage Saurus R32 on the cover) ran 10.36 @ 134 MPH and vehicle weight was 1474KG without my 105kg lard included. Car was running 27psi and was dyno'd at 404AWKW the day before.

it actually checks out...my car running in HPI a while ago (Garage Saurus R32 on the cover) ran 10.36 @ 134 MPH and vehicle weight was 1474KG without my 105kg lard included. Car was running 27psi and was dyno'd at 404AWKW the day before.

gtst should get bigger mph then gtr though??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...