Jump to content
SAU Community

R33 Skyline Parts

skymugs
 Share

Recommended Posts

skymugs Collaborator

skymugs

Posted
Posted

hey im having a cleanup and sellin all the stuff i dont need. if you interested send me a pm or give me a call 0406751986... some parts negoitiable.. everything is available to pic up or post at buyers expense

RB25 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange used 3000k's $100

RB30 Stainless highmount manifold t3/4 manifold 2 bolt 38mm wastegate flange.comes withs gaskets. new and never used $150

Coilpack wiring $20

Ignighter box $30

38mm wastegate $50

RB25 dump $20 3 avail

Exaust manifold $30 2 Avail

Ignition Barrel with genuine key $30

inter cooler piping for front mout stainless. $20

Injectors in rail.. only 5 injectors. cant find the other atm.. injectors require clean because they been sitting aeound a while. $50

Throttle body s1 and s2 $40 each

s2 tps $30

Coil packs s1 $70

intercooler pipe with adapter for blitz blowoff valve. it can replace the standard pipe in that position $30

Gredy boost Gauge $30

Genuine oil filter $10

tomie 1.2 oil restrictors x2 $15 each

Standard intake pipe with blow off valve... one with out $30 each

cam gear cover $10

Oil cooler adapter with fittings $40

300zx oilcooler $10

genuine injector to manifold seals $10

Genuine rb25 headgasket 87mm bore $50

RB25 requires rebuild. belt came of at idle and broke 2 valves in cylinder 1. had 130000 ks, run fine before that, will come with good cams as it has been sitting around for a while and the lobes are pitted. comes with oil pump and harmonic balancer, $200

flywheel will need machining $20

Genuine inlet manifold gasket where it splits $30

charcoal canister $20

Washer Bottle with motors $30

wiper motor $30

coilpack cover $20

Maroon r33 wing make an offer... also have rear bumper

r33 dash make an offer.. welcome to come inspect

silicon right angle 2.5 inch bend $20

right angle fitting in pic (not speed flow) $10

Heat shields for manifold and turbo make an offer

complete inlet manifold with injectors, sensors, idle controll valve ect.. $200

top half of manifold x2 good for changing to a forward facing plenum $40 each

bottom part of manifold $10 requires new coolant outlet

plenum chamber $20

ALternator.. has been tested $70

power steer pump $50

standard turbo to airfilter pipe with adapter and k & n airfilter requires clean $30

some standard intake pipes in the pictures if you interested let me know and make an offer

please check the link for pictures http://www.boostcruising.com/forums/index....howtopic=384000

Link to comment
https://www.sau.com.au/forums/topic/255741-r33-skyline-parts/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • EndZee
      R33 Gts/-t Abs Module Wiring Schematic (not Gt-r)

      By EndZee · Posted

      Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • dyl33
      VOLK RACING GTC CENTRE CAPS

      By dyl33 · Posted

      Centre caps $250
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Duncan
      Boost cut after swap(RB25DET NEO) R34

      By Duncan · Posted

      Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...