Jump to content
SAU Community

Recommended Posts

  • Replies 49
  • Created
  • Last Reply

Top Posters In This Topic

My front end isnt as cluttered in a HR as other models i think, plus my I/C setup is nothing like most FMIC are its close to the radiator core where as you look @ some FMIC's right down the front, making the air go all sorts of places, where the air only has one place to go with mine

Well, thats my theory on it anyway

Mine sits steady on 81c have seen it as low as 79 on a brisk morning and the highest has been 85c with spirirted driving/tuning. All of these readings were on my PFC hand controller.

Microtech dash tells me between 84 (winter) to 88 on a 47 degree day with a bit of spirited driving, it seems to hit up to 92 when the car's parked with the motor running for an extended period, but thats the highest I've seen it go, and thats with a leaking water pump! Quite impressed with it given that it's a JDM car with a small radiator being in often very hot conditions here

  • 10 months later...
My old 180 was the best, she'll be sitting on 95 most days, that's with a twin core GT-R radiator and 3 thermos... good ol' RB in a S13 chasis.. LOL.... overheat Queen!

your conservsion was shit than, my rb in the s13 while thrashing thru the hills on a hot day struggles to go past 86, cruising on the highway during the day it sits comfortably on 80-82, cruising on the highway at night time, 78-80, after steady night driving for a while and gunning it up to 200 than backing off i've seen the water temp drop down to 70 than slowly climb back up to 78-80

highest its ever been was 110, but that was a fairly long static skid! 

  • 2 weeks later...

Interesting thread.

I'm currently looking at trying to reduce my water temps, and it sounds like reducing the clutter in front of the radiator is the key.

I will take out all associated air con bits, but is there anything else I can do?

Today on a 38 degree day in Perth, on a free flowing highway going 100km/h in 5th, the water temp got to 95 on the PFC hand controller, and 102 on the Defi which reads from the top of the radiator.

Stock gauge didn't move.

^ i couldn't have more infront of my Radiator if i tried

I have

1x A/C Condensor

1x Ally Radiator

1x Small thermo fan/LH side - thats gotta be doing fk all compared to the clutch fan other than blocking air

1x Unchopped front bar, not much airflow on a HR31 bar

I have no issues on hot days. IMO i have more clutter than anyone else does.

The key is a good radiator and the clutch fan. I'm assuming that my motor sitting a bit lower is perhaps having some advantage - NFI how/why though hehe :blush:

Perhaps better 'guiding' of the air is what you need, being mine is kinda cluttered - it cant actually get out the sides and is being forced down the middle as there is little room for air to get out around the sides of anything

Interesting thread.

I'm currently looking at trying to reduce my water temps, and it sounds like reducing the clutter in front of the radiator is the key.

I will take out all associated air con bits, but is there anything else I can do?

Today on a 38 degree day in Perth, on a free flowing highway going 100km/h in 5th, the water temp got to 95 on the PFC hand controller, and 102 on the Defi which reads from the top of the radiator.

Stock gauge didn't move.

Sounds like your waterpump isn't functioning properly or your radiator is blocked.. When was the last time you had

your cooling system checked and serviced

^ i couldn't have more infront of my Radiator if i tried

I have

1x A/C Condensor

1x Ally Radiator

1x Small thermo fan/LH side - thats gotta be doing fk all compared to the clutch fan other than blocking air

1x Unchopped front bar, not much airflow on a HR31 bar

I have no issues on hot days. IMO i have more clutter than anyone else does.

The key is a good radiator and the clutch fan. I'm assuming that my motor sitting a bit lower is perhaps having some advantage - NFI how/why though hehe :blush:

Perhaps better 'guiding' of the air is what you need, being mine is kinda cluttered - it cant actually get out the sides and is being forced down the middle as there is little room for air to get out around the sides of anything

must be a hr31 thing, i cant get my car above 75.

what radiator you using brockas? still got the clutch fan and shroud?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was using the wiring diagram I have So 12.74V is coming into the rear Fuel Pump relay as I measured.  When I turn the key to ON im getting 0.6V to the Fuel Pump plug; which i assume is backfeed voltage and doesnt include the 12V from ignition power.  The rear relay is working and being triggered.  From the diagram I clearly see the rear relay 80 = Rear Relay going into the Body/H loom (R-27) 27 = Fuel Pump plug going into the Body/H loom (T-20) 40 = Short Connector (R-27) I'm reading 12.74V on the blue/black wire which is the power for the Fuel Pump   From this diagram I can see the Ignition relay goes into the front and up to the ignition  2 = Fuel Pump Relay <1M> (R-27) 37 = ING Relay <1M> I started from the pump using this reference Which the way I read it (referencing Nissan wiring color codes) is: Pin Wire Color Function 1 B/P (Black/Pink) Ground 2 L/W (Blue/White)        ECU Trigger 3 SB (Sky Blue) Fuel Pump 5 L/B (Blue/Black) 12V Constant Tested SB to SB on Fuel Pump for continuity - confirmed Tested negative on Fuel Pump to 12V battery and L/B - confirmed 12V Pulled the relay putting 12V between Pin 1 & 2 and testing continuity on Pin 3 & 4 - confirmed relay   So that has me looking at this part of the circuit to understand whats happening here...and im still confused. From best I can tell; the disconnect is back to my previous diagram; between Ignition Relay and Fuel Pump Relay...which yet again; afaik is where the immobiliser should.    Thats what I was trying to explain to GTSboy; im not trying to fix it myself; yet I seem to have to get a Masters in Electrical Engineering (while im busy doing my actual job of DevOps & Cloud Engineering) somehow.  I just wanted more expert opinions; or more so that what I tested is correct and proves it to something around that area; to go back to the alarm tech (for a 3rd time) that he needs to fix it. He keeps telling me its not the alarm. He lives on the complete other side of the city so i understand not wanting to make a trip but as I said before if its the alarm it should be up to him to fix it. But he's adament its not; even though I pointed out the FP was immobilised through the original alarm. To my mind; it seems that the ECU is sending the signal; but the ignition is not getting 12V down the line.       
    • Maybe also really stiffly sprung track cars. Get the inside wheel up in a corner and all the fun stops. Also me sometimes (rarely) when I have to stand on the brake to convince the diff to drive the wheel that is still on the ground when I'm trying to diagonally get over severe driveway entrance, etc.
    • I feel like I'm missing something. You had an authorised installer come out and install a new alarm. Post install the car doesn't start, and you aren't getting the installer back to fix what they did wrong?
    • So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
×
×
  • Create New...