Jump to content
SAU Community

Sealed Batteries $180

wrxhoon

By wrxhoon,
in Group Buys

 Share

Recommended Posts

wrxhoon Grand Master

wrxhoon

Posted
Posted

I have found some sealed batteries at a very good price, they are simillar to odyssey but don't have the steel case . I put one in my old 33GTR in 2004 , I sold the car some years ago to a guy that I know and the Battery is still going , car has alarm and a tracker in it . I have the same in my 34 GTR and a few others in this forum have them.

I compared the specs of the battery to those of the odyssey 1200 and they appear to be almost identical in every way. Even the dimensions are the same.The only difference is the steel jacket on the odyssey.

They are 20x17x17 cm , it fits it the r33 but you need another bracket , same with the 34 GTR too.

This group buy will be open for the month of March , from the 1st to 31st. The price is $180+ delivery , about $22 registered to Melbourne and Brissy.

Anyone interested let me know via p.m. you don't have to pay up front , you pay when I get them .

Link to comment
https://www.sau.com.au/forums/topic/257486-sealed-batteries-180/
Share on other sites
wrxhoon Grand Master

wrxhoon

Posted
  • Author
Posted (edited)
You got a site, where i can check on the specs champ? how good is it to power two amps and the HU, along with rest of the electrics?

That will depend on your alternator and the current your amps draw. You can always use two batteries if you have space.

Specs:

40 Amp Hour 12 Volt

Size: 197 (L) x 165 (W) x 170 (H) mm

Charge current: 4A for 10 to 14 hours

Discharge Current: 2A for 20 hours

Capacity:

20hr rate: (2A) 40.0AH

10hr rate: (3.8A) 38.0AH

5 hr rate: (6.8A) 34.0AH

1 hr rate: (24A) 24.0AH

Int resistance - fully charged: 10mohms

Constant Voltage Charge

Initial Charging current: < 12A

Cycle:

Voltage: 14.40V ~ 15.00V @ 20°C

Temp coefficient: -30mV/ °C

Standby:

Voltage: 13.50 ~ 13.80V @ 20°C

Temp Coefficient: -20mV/ °C

Weight: 14.0kg

Edited by wrxhoon
  • 4 weeks later...
wrxhoon Grand Master

wrxhoon

Posted
  • Author
Posted
interested but want to see a photo first? shipping to adelaide cost and time ?

cheers

Have a look here for pics : http://www.skylinesaustralia.com/forums/Se...ies-t62252.html

$26 registered post to Adelaide and 2-3 business days delivery.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • Kinkstaah
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Kinkstaah · Posted

      You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • Dose Pipe Sutututu
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Dose Pipe Sutututu · Posted

      LOL.... you are correct there.
×
×
  • Create New...