Jump to content
SAU Community

Xenon headlights in a 33 GTR

Canadian GTR

By Canadian GTR,
in Victoria

 Share

Recommended Posts

Canadian GTR Explorer

Canadian GTR

Posted
Posted

I have had a look through alot of threads and cant find anyone with this problem.

My Xenon lights have some marks in them that look like condensation, the stains or spots go along the entire headlight.

Has anyone come across this before, is there any easy way to open the headlight assembly and clean them ??

The headlights don't fog up, it just looks shitty.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/25842-xenon-headlights-in-a-33-gtr/
Share on other sites
Guest RedLineGTR

Guest RedLineGTR

Posted
Posted

depends if its actual water/condensation or is it marks left over from past condensation? u cant open the headlight assembly they are pretty much glued together, some people have put them in the oven to get them apart a big job and not really worth it.

If thier is water/condensation in the lights then possbily take the globes out and leave them open so air and heat can get into them, best time to do it is on a hot day or something...either driving or letting the car rest either one should work.

Canadian GTR Explorer

Canadian GTR

Posted
  • Author
Posted

BB GoDZiLa: Oh man I wish, when I bought my GTR I tried to find an LM every where, I had no luck- well actually i did find one but the guy wanted 90 grand............Ouch!!!!

When I saw that Pic I just had to have it !!

Jamezilla: A wire coathanger worked best for my lights, I did it last night, At first I didnt think it was making a difference but then I put a little degreaser on the rag the stains went away almost straight away. Try not to use a fluffy rag because it leaves fluff in side the headlight, but the good old vacum cleaner sorted that out I taped a hole series of plastic straws together and fed them inside the headlight then taped them to the pipe on the vacum cleaner and out came the small dust particles, it did get plugged a few times but it worked well.

Jamezilla Grand Master

Jamezilla

Posted
Posted

canada: Wow - nice Macguver work :(

How did you get the hanger end inside the lamp fitting? Did you need to take them off the car?

Seems there are a few Xenon GTRs around now - we should have a mini-meet :D

Canadian GTR Explorer

Canadian GTR

Posted
  • Author
Posted

I actually left them fitted, I just unscrewed the Xenon bulb, this left a large gap. It was a little akward to get into the far corner by the high beam and the the actual high beam bulb was to small to stick anything through.

Needless to say I removed my airbox, passenger side was easy.But on the drivers side I had to remove the window washer tank and the coolant run off tank- this may sound full on and even abit over board but it was hard to get the right angle with the coat hanger.

Mini meet sounds good where are you located ??

I'm in Epping/norther suburbs.

P.S. I cant imagine driving a niva after a rangie, do you ever take it off road??

Jamezilla Grand Master

Jamezilla

Posted
Posted

Cool - sounds like a nice way to spend Saturday arvo. The dirty lamps have been bugging me for a while.

I'm in South Yarra.

One magazine once said of the Niva "Great off-road, best kept there" :(

Is loads of fun - just a smidge underpowered though. Very nimble - high angle of entry and exit.

ladabank_04.jpg

brownrussian2.jpg

Jamezilla Grand Master

Jamezilla

Posted
Posted

Mine are factory fitted. Pretty sure Nissan replacements are about $2k each - not cheap.

You can get HID kits from these guys: http://www.hidlights.com.au - but I think it is a bulb conversion, not a gas-discharge unit as on the GTR.

Canadian GTR Explorer

Canadian GTR

Posted
  • Author
Posted

Jamezilla:

Theres nothing better then a 4X4 covered in mud, have you ever had any electrical problems while river crossing or puddle bashing ??

My Rangie had 33 inch tyres and a 3 inch lift kit, but when ever i got close to water it would run rough, not to mention that most of the electricals would stop working as well.....good old british enginering ha ha.

BTW your niva looks tough, maybe a little small for me.

riggaP: not sure, I have a friend with a GTST he has the Xenon headlights but the car has a complete GTR kit fitted- and he

bought it that way, I will have a closer look tonight and post back here.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...