Jump to content
SAU Community

Recommended Posts

hey got picked for a "random" drug test/alco test, and to make a long story short got defected, my exaust is to loud didnt evan messure it iwht a db metre, its a standard r33 series 1 exsaust then from cat 3" back to a 5" cannon,it had a silencer in the tip but i had it bashed out, and he looked under my bonnet and sdaid my fan shroud is to small and is ilegal, what do i do? try and pass it with a silencer, also i have a trust turbotimer, a greddy boost controller and a blitz infomation display all in the secon din pocket, are any of these ilegal?

Link to comment
https://www.sau.com.au/forums/topic/259276-defected-need-advice/
Share on other sites

set your turbo timer to 0 then they wont hassle you for that

pretty much make sure all your signals are working (breaks, indicators, lights, revers and number plate lights)

also make sure your wipers and squirters work

make sure that your tyres are good

it has to be over 11 cms from the ground at the lowest point (usually exhaust)

your exhaust will be fine, mine has no mufflers (only a cannon) and it passed last week with a bashed out cat :blink:

it has to be over 11 cms from the ground at the lowest point (usually exhaust)

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

500mm to bottom of the headlight , had a 32 pass that wasnt 100mm under car clearance

500mm to bottom of the headlight , had a 32 pass that wasnt 100mm under car clearance

That's probably another of their little tests. When I went over, there was a 100mm bump and the inspector said that if I scraped, I was too low.

He didn't measure to the headlights, he measured the eyebrow level and told me I had to put a 10mm block under the rear spring?!?!?!?!?!

What they'll pass you for depends on whether they got a root the night before.........

^ here here

when i was at the pits i was told it is 100mm for the lowest part of the car (does NOT have to be solid - ie. my bodykit was measured as it was lower than my exhaust)

WITH a car load of grown adults AND a full tank of fuel

that's my personal understanding, i got let off as i had adjustable suspension because they check that too, let off with a warning to get a permit for the suspension asap so if you have adjustable suspension that may work in your favour

Edited by hoony
100mm with a full car load as well.

My car was 100mm exactly with nobody in it, inspector passed me with a warning on that one!

HAHA... bloody inspector failed me even with 100mm. He says if there was 5 ppl in the car it will be less than 100mm. That was his reason for failing me. OH stock car! So good luck!

^^ Rock hard billsteins here mate :) Passed fine (5 ppl would probably drop it half a cm max.. lol)

The problem is its a STOCK CAR! If it was lowered or modified in anyway i would understand. Told him thats the build of the car, its lower than most car even with stock springs and suspension.

100mm in WA. And it's only for solid items like the exhaust. Flexible items like mudflaps etc. are ok.

This pissed me off when I got done becuase the inspector told me of a recent Merc that was brought out from the factory and passed that had an 85mm clearance.

Typical..........

the A series merc had a 85mm clearance where the oil sump was the lowest part of the car. This had a manufacturer warranty with it meaning that if anything happened to the oil sump, merc will have to fix it or give you a new one.

I was told it was a 100mm clearance from the lowest part of the car excluding mud flaps.

Do the simple things:

Degrease engine bay and gearbox.

Make sure car is as said 100mm of ground everywhere.

Headlights are 500mm of ground.

Put in silencer to exhaust.

Depending on which PITS you got they have different ways of test height. They usually drive over a speed bump. If it scrapes, too low. Pits have different height ones. Heard welshpool is 85mm and another one is 140mm

Fan shroud is just a way of getting you stickered cos u wouldn't know the regulations about it. Similar to tyres. How do you disprove that they weren't bald when the cop issued sticker. So have good tire depth. Gadgets aren't illegal as long as they are not inpairing vision of drive.

But yeh, stickers are a cops way of making it harder for you as a car enthusiast. And to scare people.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
×
×
  • Create New...