Jump to content
SAU Community

Recommended Posts

Just got my Skyline gts-t 33 back after it was sitting for 4 months and i think i have got a blockage and would just like to know where it is located on the car so i can have a look.

MIne is on the drivers side of the engine next to the strut tower, big shiny silver sucker.

Link to comment
https://www.sau.com.au/forums/topic/260156-fuel-filter/#findComment-4465336
Share on other sites

Hot water helps, but trying to get the hot water anywhere near the fuel hose if you have aftermarket parts near the fuel filter make it hard.

Trying to get the hose off takes forever if it hasn't been done for a long time :D

Link to comment
https://www.sau.com.au/forums/topic/260156-fuel-filter/#findComment-4466825
Share on other sites

  • 6 months later...

Guys im a complete noob and im trying to replace my fuel filter cos it seems kinda sluggish and hasnt been done b4..only a recent owner. Any precautions i have to take b4 i replace the fuel filter? cos atm im thinking u just flip the hoses off and replace it thanks guys

Link to comment
https://www.sau.com.au/forums/topic/260156-fuel-filter/#findComment-4823117
Share on other sites

Guys im a complete noob and im trying to replace my fuel filter cos it seems kinda sluggish and hasnt been done b4..only a recent owner. Any precautions i have to take b4 i replace the fuel filter? cos atm im thinking u just flip the hoses off and replace it thanks guys

Thats the way.

Have some spare hose with you before you start. Because as many have done, you sometimes need to slice them off.

And a supply of paper towels and band aids :P (for the hand you will mash against a sharp bracket)

Link to comment
https://www.sau.com.au/forums/topic/260156-fuel-filter/#findComment-4826358
Share on other sites

start car

open boot

pull fuel pump fuse (top 15a fuse)

car will stall

loosen fuel cap

start/turn car over until lines are clear

cut the old hose&filter off at each end and remove as a complete assembly (if its easy to remove its probably been done before so skip replacement)

replace with new hose (1/2" about 600mm req'd) and new filter (Z200)

Link to comment
https://www.sau.com.au/forums/topic/260156-fuel-filter/#findComment-4827490
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...