Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

a r33 gtst will get s14 and a s15 , is the 300zx turbo? the 180sx s/2 has the same motor as the 200sx as the new one, i had a 97 180sx they are qucker than r32, i think they go good as wrx,s. i had a race with a 200sx the new one in a r33 gtst and it had a big front mount and i beat it by 3 car leanth we raced up 2 about 120km

not to be bias but i say the s14/s15 should beat the r33 (from past experience). Not sure about the 300zx though. R33's are heavier than the s14/s15 and between the s14 and s15, the s15 should win due to a ball bearing turbo, lighter body and better diff. A friend of mine has a stocky 180sx and that used to beat my s14 when stock and another friend's stocky r33 too. But im sure that 180's shouldnt be THAT quick normally, just that his happens to be a bit of a freak. :)

Does it really matter? They can each be modded off their tits to beat any of the others, just depending on how much money you want to throw at it.

That's why I bought the car that I like best for reasons other than how fast it is down the 1/4 mile. And the mods that it came with made it faster than any of the aforementioned when stock. So in theory I got the best of both worlds :P

Originally posted by JimX

Does it really matter? They can each be modded off their tits to beat any of the others, just depending on how much money you want to throw at it.

That's why I bought the car that I like best for reasons other than how fast it is down the 1/4 mile. And the mods that it came with made it faster than any of the aforementioned when stock. So in theory I got the best of both worlds :P

:werd:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...