Jump to content
SAU Community

Recommended Posts

I got my car tuned a few months ago with a haltech intercepter and the temp that day was around 40deg. The car was running fine untill a week ago. Now when you rev a gear out it starts to pull then it has no power, It feels like it just cuts off. I was wondering if because now the days are around 25deg would the air be colder/denser and it's leaning the mixture up causing this problem? I have also noticed that the exhaust out the back is hotter than i remember.

Thank You

no. your fuel pump is no good. or its supply. stick a guage on it and take it for a hit. deffinatly nothing to do with the tune..

mine was done in similar heat. no drammas at all in freezing gouburn

But it's a new pump. And sometimes it will run fine and other times it will play up. i usually find it will play up in 3rd gear.

Could just be over boosting abit in the cooler air and hitting the boost limit .... have you noticed the gauge when driving being a tad higher ?

If you have access to the boost controller / bleed valve etc , try turning it down abit to see if it help.

Gary

Edited by Fastrotor
Could just be over boosting abit in the cooler air and hitting the boost limit .... have you noticed the gauge when driving being a tad higher ?

If you have access to the boost controller / bleed valve etc , try turning it down abit to see if it help.

Gary

I have a EBC and it isn't spiking. I holds boost perfectly

But do you know what the cut is set at in the haltech ? perhaps it was set too close to the mark, and the difference isnt noticable to you on the gauge ? Can't hurt to try turning it down a couple of pound just for a test, if you've run out of other things to try that is.

Gary

But do you know what the cut is set at in the haltech ? perhaps it was set too close to the mark, and the difference isnt noticable to you on the gauge ? Can't hurt to try turning it down a couple of pound just for a test, if you've run out of other things to try that is.

Gary

It will even play up on 6psi

I got my car tuned a few months ago with a haltech intercepter and the temp that day was around 40deg. The car was running fine untill a week ago. Now when you rev a gear out it starts to pull then it has no power, It feels like it just cuts off. I was wondering if because now the days are around 25deg would the air be colder/denser and it's leaning the mixture up causing this problem? I have also noticed that the exhaust out the back is hotter than i remember.

How are you testing the EGT? Any chance you have a leaky blow off valve or some other intake leak forming?

I replaced the fuel filter a few months ago and the compression is fine. I went back to the workshop that tuned my car and as usuall they were useless and rude. I decided to drop the base timing back alot and now the car doesn't play up.... it idles really low now but i will adjust that soon.

  • 2 weeks later...

ok i have set the base timing to 15deg with the TPS cable off. I noticed that the timing jumped up a fair bit when i pluged the cable back in but i guess that is pretty normal. But driving it after that it still feels like the power cuts as you rev out the gears. The only other thing that im wondering is i have heatrange 7 spark plugs in there and the std coils. Now i dont know much about exactly how the different heat ranges affect different things. I know that when its cold it runs like a dog thats fine but should i go back to heatrange 6 plugs till i get splitfire coils? Or could i just be barking up the wrong tree?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...