Jump to content
SAU Community

Recommended Posts

Hi guys,

I am having some white-ish(theres a mix of white and black smoke) smoke coming out from my exhaust when i hit full boost. Read a few threads but all seems to point to the turbo seal.

The turbo on my car is a brand new HKS turbo hence i dont think it will be the turbo seal. No smoke of any kind when it is idling. Just on boost, you can see a cloud of smoke.

Any ideas what could be the problem?

Thanks inadvance!! :cool:

Link to comment
https://www.sau.com.au/forums/topic/260705-white-smoke-on-full-boost/
Share on other sites

Hi guys,

I am having some white-ish(theres a mix of white and black smoke) smoke coming out from my exhaust when i hit full boost. Read a few threads but all seems to point to the turbo seal.

The turbo on my car is a brand new HKS turbo hence i dont think it will be the turbo seal. No smoke of any kind when it is idling. Just on boost, you can see a cloud of smoke.

Any ideas what could be the problem?

Thanks inadvance!! :cool:

Aren't you supposed to do a break in before going full boost with your new turbo? Problem might not be with the turbo seals but the other oil seals in you engine. Since the new turbo would be pushing more pressure, those seals might have gotten worn out faster than expected.

White smoke when car is cold = evaporating water condesation

White smoke when accelerating = oil < from turbo, oil rings >

Blue smoke if what desiels blow normally,

Black smoke is octane. Either over fueling or not enough spark.

Is it making same power as before. If its just has a rich tune or lack of tune and is running rich it will blow black smoke = over fuel.

Thats fine.

post-40804-1236922154_thumb.png

Is it making same power as before. If its just has a rich tune or lack of tune and is running rich it will blow black smoke = over fuel.

Thats fine.

I am having some problems with my tune. send it back twice and the engine light is still popping out on low boost 0.85 bar(10 psi?) Havent been driving on high boost.

This is the dyno graph and i reckon its a bit a rich side. Black residue all over my bumper and garage door. And also i did have lots of misfiring problems with even with new plugs and splitfires.

Turbo oil seals.

Otherwise, engine issues (rings, etc)

Daniel has alot of experience with this :banana: ey daniel lol.

normally id be going straight for the turbo seals but being a new turbo that makes it abit unlikly that the seals are failing already,but anythings possible right!?

if the smoke is a white/grey colour under boost then check your cooler and intake piping for blow-by, check your catch can (or get one if you don't have one) and do a wet and dry comp test on your motor checking for consistency and drop differences.

after this you will have an indication if the problem is your motor or your turbo.

Edited by dmr

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...