Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

I burnt my pipe last night, if that counts?

:\

In other news,

I was gonna come out last thursday but you know, not driving a riceline and all I would feel left out. Plus, I don't have a hat.

Edited by hylian
Nice nice.

Burnt your fingers yet?

If you burn your fingers your doing it wrong

*twirls pipe*

im soo getting my hat on on thursday

Flat cap ?

I burnt my pipe last night, if that counts?

Depends on what type :bunny:

Dont worry about not having a riceline.

Geez, i drive a maxima-wannabe. Its not a maxima but isola enjoys arguing that it is.

Get a hat though. And if you can a pipe.

I was gonna come out last thursday but you know, not driving a riceline and all I would feel left out. Plus, I don't have a hat.

Come out anyway. Jason and I are both big Ford fans. You can hang with us :bunny:

If you burn your fingers your doing it wrong

+1

As for type... a genwine old school corn pipe... only the best tobaccerrr for this ollle farmer

Morning Mangs

Keen for hat tipping, keen for pipe (that's what she said)

OMFG I JUST CLICKED THAT 'Kittens in tiny hats' LINK WITHOUT REALISING IT WAS YOUTUBE AND IT WORKED!!! WTFONEONEONEBARBEQUE

Need to start bringing headphones to work I think :D

your at your desk at work at 7:39am

By 7:15 normally. It's by choice though, I do it so my trips to and from work are half an hour not an hour.

sucks to be you

I was going to say no, because I get to go home at 3:15, but then I read this:

ill get to mine around 10, and be home by 3... :D

:(.

What do you do btw?

Blocked website at work hey?

Not at mine. I can watch as much p*rn as I like.

granted I work from home though :)

Pootube used to be blocked, but they upgraded the filters recently and it must have slipped through.

Massive fail though, I just clicked on a thread in wasteland and got a big "DENIED! ADULT MATERIAL PRON ETC YOU HAVE BEEN NAUGHTY!!!!" message and now it seems the whole of SAU has been blocked :(

Now I have to use this sh*t slow connection I have h4xed to bypass the filters.

The work from home option is sounding good, I now can't access SAU or my personal email without h4xing, plus I have sh*t small desk. I should be able to a fair bit of work from home soon. At the moment though, I don't have any work suitable for taking offsite :(

What is it that you do that you get to work from home?

account manager

work in wholesale with the major CE retailers and FMCG retailers...

basically been in sales now for 11 years...

Eat a bagel, like a boss... send some fax's, like a boss... etc etc

spose i better go iron a shirt and go to work...

need to stop by the bank and post office etc on the way... might take an hour...

also feel like a HJ's brekkie wrap for some strange reason today... ummmmm

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...