Jump to content
SAU Community

Inner West Crew Whoretown (toowong/st Lucia/kenmore/indooroopilly And Sometimes Sunnybank?)


Recommended Posts

can any of you guys draw ??

as in engineering drawing?

need a template measured and drawn.

how complex Chris?

I did graphics in grade 9 & 10 and have CAD software here at work, if it's not too hard I may be able to manage it.

R32 GTR tach panel - need to make a drawn copy of it and indicate what area needs to be clear for a 4.3" lcd to sit behind it.

doing a retro nismo display for my 32.

nah piece of piss in comparison to that. I will pull the cluster and take the relevant bit out of it. you can make the call off that.

Well, finally got the stag back after being without her for about 3 weeks. Received 2 A4 pages of work done and half a page of items replaced totaling $3795 (ouch). But from the tiny amount I've seen so far it running a million times better. Pretty well completely stock apart from pod filter and exhaust system. Now I just gotta pay that off, save some more to do the suspension, fix the VCT and a few other minor bits and pieces. Need more monies so I can get moaw power. Very happy so far though.

205.2HP @ 7.5PSI with at least another 80HP once VCT and small leaks fixed.

Edited by Grimi

Hi I'm new 2 the site and just wounderin where and when u's are meetin i wouldn't bringin out my r33 gtr!!!! Can anyone attend and do many people turn up????

if you are who I think - why haven't you popped up sooner..

Good online stores to buy shoes / shirts from. Looking to replace my now stolen Vans block letter shirt and need new shoes. Went to Chermside tonight, absolute nightmare. Now resorting to online shopping from now on.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...