Jump to content
SAU Community

Recommended Posts

So well I broke the little cheap plastic thing when I was changing my light for LED on my cluster. So I ordered my cable from nissan. I searched a lot. and I learn that the cable is connected to the gearbox and pass throught the firewall.

But euh.. does some have picture of where exactly it goes? and how do you disconnect it? Will I have to change the fluid after?

Thanks :D

I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

I assume this in an R32 ?

There are three bolts to undo in the engine bay, near the steering column. Undo these, pull cable to the left in the cabin, and it will come out from its slot. Pull from the engine bay, making sure now and then it's not getting caught on something. Crawl under car, unclip cable from brackets, unscrew shield from gearbox..

Fit new cable reverse of this.

No you will not have to change your gearbox oil.

So I tried to change it today. WASTED 3 HOURS OF MY TIMESicon_ChairShot.gif.

How the heck do you UNBOLT THOSE 3 BOLTS?? Is there a special tools? I can't do it with a tiny screwdriver because I don't have enought force. With a long screwdriver it just wont fit.

And with a ratchet, I don't have enought space to ''wind up''

PLEASE HELP!001_help.gif001_help.gif001_help.gif001_help.gif001_help.gif

My car is a BNR32

Edited by cobrAA

You will need a socket, or spanner (I think it's a 10mm) and nimble hands :) but no special tools required. There isn't much room I agree to move around, maybe less so on a GTR.

If you jack up the car, it may be easier to do it from underneath.

Yeah 10mm bolts. 3 of em. ratched with extensions is all you need. The whole plate comes off the firewall. I did have my dash out as I think there is a clip just before it goes into the back of the cluster.

It's a simple job.

Okay . 4 hours later. Job is still not done. So I'm down to a 6 hours spent and still not done...

How do you insert the gearbox cable end STRAIGHT??? I spent the last hour trying to bolt it but it will always go too much to the right, too low, too high. It just wont ****in go straight and fit so I can bolt it.

I did insert the metal piece in the hole of the gear box but I just can't bolt the bolt on the gearbox because it is misaligned..

Please Help serioulsy. I'm really about to sell my gtr because of that freakin stupid 70$ mods.

umm i thought the cable that fits into the gearbox end has a notch and fits only 1 way.. bugger.. maybe try with the old cable on the gearbox to see how it fitted

For sure it is one way, but since the cable is so ''strech'' it wont hold in place. so it will make my bolt ''offset'' so i can't screw it forward.And the force is so big that I can't hold the cable at the ''right'' place with one hand and screw with the other.

Hope you understand what I mean?

Edited by cobrAA

have u already plugged in the other end to the cluster?? from memory, my cable had a nice loop before coming into the gearbox, certainly wasnt strained like yours??

dont know if gts-t cables are any shorter, maybe wrong cable supplied by nissan.. gts-t ones have few teeths to the gtr so wont work on gtr but not sure if length is different

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...