Jump to content
SAU Community

Recommended Posts

i did the change. also went from a pfc to a wolf v500, with a much more in depth tune so i can't really coment on possible response loss, as i actually gained a lot of throttle response.

only ill effect i noticed was a small increase in the amount of times the car cranked over before it started. like maybe half a second.

There are many automakers who use MAP based systems with no problems at all, so why would you have problems with a map based standalone? If there were problems you can probably chalk it up to bad tuning or just a poorly designed standalone. I have zero problems with my standalone map based system even though I have a 5bar map sensor. Cold start, Drive-ability, Closed loop wide band Cruise, and deceleration are perfect.

Edited by maximajim

I went from ECR33 PFC L-jetro and converted it to run the GTR's D-jetro, Being that I mapped both setup's I can say this, the D-jetro was much easier to get nice dead stable AFR's, Drivability is better and fuel consumption is up by .5L better per 100km. (this was with no other mods done at all besides ECU change, I use FCedit, dual widebands, EGT and dual knocklinks when mapping RB's)

Best thing, no idle mess around! car just runs better all round. D-jetro's idle stabilization by timing is fantasic as well! almost as good as VEMS's

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

Edited by moneypit
I would say buy a ecu based on his recommendation or find another tuner who is competent in tuning a map system.

He should know that a good standalone will have temp and barometric trims (if needed).

He recommended going map, ecu is hks f-con,

but he just said it will feel different, and indicated I might not prefer it.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

MAP sensor here too. Given the choice, i'll always go MAP over AFM. The number of AFM related issues that seem to pop up all the time is crazy. I went through 3 AFMs on my old car, and it still never was quite right.

100% agree

MAP user here :D

so far then .. it sounds all good.

I wasn't told map has any "problems" but that it isn't a good choice if you plan

to do mountain driving, as altitude (or big temp changes) muck with the tune vs maf.

My tuner says map will "feel different" in a possibly negative way, he didn't elaborate.

And people on sau have posted before that map is 'for race cars' and maf is for street,

and someone else on sau said map didn't work as well with multiple throttle bodies.

So I figured I'd ask if people had experienced a car before vs after with as much else

the same.

The issue with multi throttle bodies and MAP, is the turbulunce.

You can get the same MAP reading, for a different throttle reading, and it plays havoc.

Good ECU's, like the Adaptronic, Motec, (I also believe Haltech, ViPEC and Autronic) run MAP vs TPS tuning.

I run MAP with the Adaptronic, and it has no issues at all.

Actually, it has quite a few benefits... I can run NO BOV, and not have a single issue.

I run an oil coated air filter, and not have it flood my AFM giving shit readings, resulting in poor idle...

Yeah mine doesnt take long to crank, and doesnt hunt on cold start. It does everything "normally" compared to an AFM based ECU.

....Well, except for having dramas when the AFM's get dirty and play up :D

Ford XR6 Turbo runs map and no issues there. So the whole map = race car is a little off.

The 1JZ and I believe 2JZ also run MAP...

Lots of manufacturers cars run MAP from the factory

My car takes a couple of cranks to fire, but that is purely the ECU, and NOTHING to do with it being MAP based.

I went through 3 AFMs on my old car

Brand new each time or 2nd hand? I'd be interested to hear the reasons why 3 brand new AFM's would have died in a short period.

If 2nd hand, then well... thats pretty much a pointless statement :D

Every AFM that i put in (new) works/worked fine without issue.

Ive played around with 2nd handies lately (due to time constraint) and had nothing but problems, but i accept that because im playing around with used parts and not brand new ones.

That said - go with what the tuner reccomends. He is tuning it afterall...

Straight MAP was poor on light throttle compared to AFMs but I had multiple throttle bodies (RB26). Redid the tune with MAP over TPS (combination of the 2) and found driveability every bit as equal as stock AFMs.

Best point => if I blow a cooler pipe/vacumm hose at the drags I can drive it home as is... unlike AFMs which would instantly foul the plugs. Best move I ever made was getting rid of the AFMs.

I went for a MAP because my tuner prefers it, he put it this way to me, although the AFM is a good bit of gear he has had more problems with that one piece of equipment than any other but finding out it is the AFM to be the problem is the real reason he prefers the MAP sensor, as for driveabilty I didnt really notice anything except the power increase.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...