Jump to content
SAU Community

Recommended Posts

hey, i have a black r33 spolier for sale, came off my series1 gts, but isnt stock spoiler, i believe it is m-spec spoiler, but not too sure whether it is or not.

spoiler is in relatively good condition, a couple little stone chips but barely noticeable.

im in melbourne, northern suburbs, but can arrange pickup or delievery with the buyer. im asking $150 negotiable, if interested pm me or call adam - 0401 321 013.

post-52996-1239354519_thumb.jpg

does it have a light mounted in it? doesn't look like it in the picture.

and no offence but there is no such thing as a m-spec r33. that is a r34 gtr type. the r32/r33 was type m. and the wing is based off a series 2 wing, but bigger.

does it have a light mounted in it? doesn't look like it in the picture.

and no offence but there is no such thing as a m-spec r33. that is a r34 gtr type. the r32/r33 was type m. and the wing is based off a series 2 wing, but bigger.

yeh same shit, nah no light, but yeh, it must be whatever you said, i just got told its off a type m* r33

does it have a light mounted in it? doesn't look like it in the picture.

and no offence but there is no such thing as a m-spec r33. that is a r34 gtr type. the r32/r33 was type m. and the wing is based off a series 2 wing, but bigger.

thats not a R33 Type-M wing, correct.

R32 and 33 type-Ms existed, R34 didnt have an M-spec tho.

needless to say this wing would need a phat kit to set it off

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...