Jump to content
SAU Community

Recommended Posts

Some questions about this.

It's an amplifier, but it's accepting an amplified signal already, ie the speaker output from your headunit which will typically be 22W RMS, however the rear speakers are only rated for 8W RMS. I haven't looked at the front ones.

Does it just drive the rear speakers or does it drive the front ones too. If it's just driving the rears then is it perhaps a high pass filter and the rears are just tweeters with the fronts being full range?

If it is actually an amplifier and drives all 4 speakers is there any way to trick it into accepting a line-level input as this will allow me to simplify my Car PC install dramatically as I'll just need to glue my USB soundcard to the amplifier and make up some leads rather than do a full amp+speakers installation.

the box is the rear amp it drives only the rear speakers i removed mine and spliced and soldered the wires together because it stuffed up and i wasnt getting a signal to my rear speakers any more its useless most decks perform better than 80's junk any how

  • 3 weeks later...

ok... so i removed 2 boxes today... (car did have hicas / abs etc..)

are they both amplifiers?????

one is a small one about 8cm x 3cm taken from under parcel shelf on drivers side moreso

the other is about A5 size... taken from just off centre moreso toward passender side from under parcel shelf.

they both for stereo???????????????

ta

  • 3 weeks later...

i have 3 unidentified boxes lol,,,

huge on on the passenger side bigger than computer silver with 2 looks

another in the middle ( the amp i think )

and 1 on drivers side much smaller with just 1 loom to it ?

anyone know what these are yet ?

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...