Jump to content
SAU Community

Recommended Posts

Crap brand and/or bald front tyres causing your car to understeer in the wet.

With the wheel spin your diff is probably loosening up from old age.

thanks for that

well my front tyres are new with around 90% tread on it

they must be shit than lol

well i own a 1993 r33 with 180 000kms

but in the dry it spins both wheels

thats what i dont understand??

Link to comment
https://www.sau.com.au/forums/topic/265233-ecr33-diff/#findComment-4531008
Share on other sites

you have a viscouse lsd (sorry for the miss spell) means it wont allways catch lsd. so in the wet its too easy for it to brake traction and doesnt need to spin both. though like hamish said it is probably a bit worn (wear will make it looser and wont catch as oftern)

to fix this you could shim the diff which will make the diff tighter, just dont shim it too far or the diff will be locked. you can buy the shims from nissan for about 5 dollers each, you probably will only need one .8mm one. by memery it will take about 2mm to lock it. its not difficalt to do just a bit of work there should be something in the DIY section telling you how to do it.

panda

Link to comment
https://www.sau.com.au/forums/topic/265233-ecr33-diff/#findComment-4531669
Share on other sites

What brand tyres do you have on the front? Also is the wheel allignment to spec? Because that can also affect understeer/grip. Another factor could be that you have wider tyres on the rear and skinnier tyres on the front causing the rear to force the front to understeer by the rear having more grip.

On the diff, I agree that you should shim it to tighten it up. The viscous lsd's do tend to single spin once they have loosened up over time.

Link to comment
https://www.sau.com.au/forums/topic/265233-ecr33-diff/#findComment-4531802
Share on other sites

i dont think its undrsteer because the front wheels dont grip at all and slide when its wet when i turn hard

it the dry it grips and handles really good

either you've got ordinary tyres or the road surface is very slick and there just isn't much grip when it's wet. I have RE001's and sometimes find the wet grip to be pretty borderline, I was expecting more from Bridgestone's "premium" tyre. However road surface makes a huge difference, old polished bitumen has low grip while rough bitumen still grips well in the wet.

Rear diff choice does affect off-throttle handling, my R31 had a locked diff and would understeer badly into corners if I went in a bit hot. Any car with a 2-way would be similar but not nearly as bad. Standard viscous LSD will have no effect off throttle, they aren't exactly a tight diff.

Link to comment
https://www.sau.com.au/forums/topic/265233-ecr33-diff/#findComment-4541143
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...