Jump to content
SAU Community

Recommended Posts

This thread has made me see why people hate us in skylines... come on guys use common sense.

If your at the front of the lights there will be oil in the wheel lines (road indented).

try this:

1. move the car to the left or right of the lane to get off the oil.

2. park back a little from the lights so not to be right in it for your back tyres.

3. just nudge the car until the back wheels pass the white line and then give some gas.

o and obvious one is get better tyres or a problem i see a lot get your camber fixed so your whole tyre has contact with the road.

doesn't matter were u drive the oil is everywhere.

seriously its not that hard to drive a skyline in the wet. i have NO issue with not spinning the wheels in my 350hp+ skyline.

Also you should note that getting better tyres won't solve the problem as MOST soft tyres (performance tyres) have poor grip level in the wet

Edited by [Michael]
  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

thanks for the replies fellas. i got a driving course coming up soon, should get my moneys worth outta that. so i gotta pick up some t1r's and check the camber. i haven't locked off hicas, does anyone find it to be troublesome in the wet? or at all really? cause this car is a daily driver for me, so i dont need to lock it off for performance reasons.

doesn't matter were u drive the oil is everywhere.

seriously its not that hard to drive a skyline in the wet. i have NO issue with not spinning the wheels in my 350hp+ skyline.

Also you should note that getting better tyres won't solve the problem as MOST soft tyres (performance tyres) have poor grip level in the wet

I agree & um, disagree.

No car is difficult to drive in the wet. If you can't take off from a set of lights without wheelspin you shouldn't be driving. Or won't be for long after plod sees you.

But the only tyres that suffer unduly in the wet are R compounds & cheap "performance" tyres. The reason you pay good money for good tyres is that they grip well in all circumstances.

Seriously if you think that getting sideways in fourth on a wet road is testament to you driving ability you need to think again.

:P

Things to avoid are:

1. Driving like a dickhead.

2. Bragging about it on an internet forum.

I can see how you would take that point of view from what I said but I think you've taken it a little out of context.

Getting sideways in fourth fear is definitely not a testament to my driving ability rather quite the opposite I was overtaking the friend I was travelling with and was not expecting it to break loose in such a high gear/low revs. All up it was a fail and I have a new found respect for/fear of my car in the wet.

mate, next time just select second gear

make sure your window is down

make sure your right foot is firmly pressed to the floor

and remember to shake your fist out the wondow while shouting "DORRRIFTOOOOOOO"

On the track, privately owned road or controlled environment of course. Not the fist, go the 'cuda lol......doooooorrriffffftooooo11ty.

Yeh the Wet is the Unpredictable Factor... you don't know how much distance or buffer to give until u know the car's limits.

Changing to a Better Tyres help a lot. My Rear tyres was almost bald n was shocking in the wet, then i changed over to new ones and made a big difference. I felt more confident in the car but i haven't pushed the limit of the tyres of how much i can give it cuz i got used to being so carefull on my near Bald rear Tyres :-)

thanks for the replies fellas. i got a driving course coming up soon, should get my moneys worth outta that. so i gotta pick up some t1r's and check the camber. i haven't locked off hicas, does anyone find it to be troublesome in the wet? or at all really? cause this car is a daily driver for me, so i dont need to lock it off for performance reasons.

i think hicas is great, though many others may disagree an have locked it off an what not but in my personal opinion i love it its great for corner turning at higher speeds an it hasn't affected me for drifting wise, but yea i think its good... just my 2 cents

When i first got the skyline i spun it in the wet cos the tyres were crap. 3am though so luckily there was noone around.

Everyone loses it sometimes, and thats when you realise the limits of your car. Once you find those limits you know what level you can/should drive at so that you don't reach them again on public roads.

steering work as well. in the wet, if you turn your steering wheel too hard or like turning it too quickly going into a corner, your car will either understeer or oversteer (depends on how fast your going) also if you are in the middle of the corner and you suddenly jerk the wheel hard to either direction like say going into an 'S' corner, you can loose traction as well. the key is to be smooth with the steering work as possible.

my car looses traction when it hits boost and thats with pretty much new Bridgestone Potenza RE001 tyres(255/40/17 rears), soft setting on the rear dampers and stock boost :S but thats only if i press the pedal halfway or more. no problems when taking off the lights tho.

Edited by R33_NICK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...