Jump to content
SAU Community

Recommended Posts

Hi guys

Just wondering if anyone has ever purchased a car from NSW to QLD. I would like to hear people expriences who have done this ?

1. How did you transport the car ? drove it up / or transport company

2. If driving it back up to QLD what registration does it involve ?

3. How much roughly dose it costs to transport a car ?

Thanks for everyones help

Link to comment
https://www.sau.com.au/forums/topic/266006-purchasing-a-car-interstate/
Share on other sites

My V35 was trucked up from NSW to QLD cost was built into purchase price but on average I'd say around $300 - $500 depending on who you use. Car had 3 months NSW rego courtesy of car yard, so I drove it in QLD until it had about a week left, then went and got a safety certificate (most mechanics can do this, usual chk on tyres, leaks, rust etc...just roadworthy stuff) , took it to QLD transport and got new plates for it and that was it, easy.

I would never truck it..

As "Great ocean road" and your new "dream" car comes into play...*pants tighten*

I would always make sure you drop the oil, plugs, filters and what not after i buy 2nd hand cars.

couldnt hurt to do a coolant flush too.

Hi guys

Just wondering if anyone has ever purchased a car from NSW to QLD. I would like to hear people expriences who have done this ?

1. How did you transport the car ? drove it up / or transport company

2. If driving it back up to QLD what registration does it involve ?

3. How much roughly dose it costs to transport a car ?

Thanks for everyones help

1 - drove it. got unlicence car approval from RTA

2- went to RTA with original owner got temp rego - paid $35. tossed my trade plate on it when I crossed the border.

tried to do a trade plate from sydney to brisbane - told by the police not to as I would be driving a unregistered vehicle. this is a bit of a grey area and hot potato as I go 4 different answers from 4 different stations and the RTA. one said yes I could 3 said no. I took the safe option.

3 last one I trucked from sydney was $600 to rosewood - that was in '06. when I drove the last one up it took $110 to do it inc rego and 10 hours travel that was june 08.

Edited by Chris Rogers

I'd drive it.

However I made the mistake of driving a RX7 with no more than 50mm of clearance from Townsville to Brisbane in a single night, needless to say pretty much all my suspension bushes were f**ked and I had to purchase a brand new coilover kit.

Would definitly reccommend you drive it back. Drove my rx7 from Sydney back to Bundaberg because it still had nsw rego on it and had so much fun. Some really nice fun roads along the way and i learnt so much about the car in such a short time.

Drove it round for a couple of months till the rego ran out then went and got a road worthy and took it to queensland transport.

Drive up.. you can leave their plates on it then.. Get a RWC done, then take the plates and RWC to QLD transport. They give you new plates and a refund (NSW Trasport do but can be done through QLD Transport) on the remaining amount..

I wouldnt necessarily recommenfd driving around for the remainder of the rego (depending on what's left) as you want the car in your name, and if there is mods/etc that won't pass RWC then you have time in which to get them sorted.. Buying from dealer ensures that you got a good chance of passing RWC but you still never know..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I neglected to respond to this previously. Get it up to 100 psi, and then you'll be OK.
    • I agree with everything else, except (and I'm rethinking this as it wasn't setup how my brain first though) if the sensor is at the end of a hose which is how it has been recommended to isolate it from vibrations, then if that line had a small hole in, I could foresee potentially (not a fluid dynamic specialist) the ability for it to see a lower pressure at the sensor. But thinking through, said sensor was in the actual block, HOWEVER it was also the sensor itself that broke, so oil pressure may not have been fully reaching the sensor still. So I'm still in my same theory.   However, I 100% would be saying COOL THE OIL DOWN if it's at 125c. That would be an epic concern of mine.   Im now thinking as you did Brad that the knock detection is likely due to the bearings giving a bit more noise as pressure dropped away. Kinkstah, drop your oil, and get a sample of it (as you're draining it) and send it off for analysis.
    • I myself AM TOTALLY UNPREPARED TO BELIEVE that the load is higher on the track than on the dyno. If it is not happening on the dyno, I cannot see it happening on the track. The difference you are seeing is because it is hot on the track, and I am pretty sure your tuner is not belting the crap out of it on teh dyno when it starts to get hot. The only way that being hot on the track can lead to real ping, that I can think of, is if you are getting more oil (from mist in the inlet tract, or going up past the oil control rings) reducing the effective octane rating of the fuel and causing ping that way. Yeah, nah. Look at this graph which I will helpfully show you zoomed back in. As an engineer, I look at the difference in viscocity at (in your case, 125°C) and say "they're all the same number". Even though those lines are not completely collapsed down onto each other, the oil grades you are talking about (40, 50 and 60) are teh top three lines (150, 220 and 320) and as far as I am concerned, there is not enough difference between them at that temperature to be meaningful. The viscosity of 60 at 125°C is teh same as 40 at 100°C. You should not operate it under high load at high temperature. That is purely because the only way they can achieve their emissions numbers is with thin-arse oil in it, so they have to tell you to put thin oil in it for the street. They know that no-one can drive the car & engine hard enough on the street to reach the operating regime that demands the actual correct oil that the engine needs on the track. And so they tell you to put that oil in for the track. Find a way to get more air into it, or, more likely, out of it. Or add a water spray for when it's hot. Or something.   As to the leak --- a small leak that cannot cause near catastrophic volume loss in a few seconds cannot cause a low pressure condition in the engine. If the leak is large enough to drop oil pressure, then you will only get one or two shots at it before the sump is drained.
    • So..... it's going to be a heater hose or other coolant hose at the rear of the head/plenum. Or it's going to be one of the welch plugs on the back of the motor, which is a motor out thing to fix.
    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
×
×
  • Create New...