Jump to content
SAU Community

Recommended Posts

Got alot of parts for sale which i have accumulated over the years. Everything is in good working order unless stated otherwise. Located in Emerald, Victoria. Photos will be put onto photobucket

http://s160.photobucket.com/albums/t177/Shano3000/ will take photos of parts on request aswell.

Wrecking complete R33 GTS-T.

RB25DET Complete Engine 100,000km. Will include everything minus engine loom. Very good condition with stock turbo. Had its major service 3,000km before crashed. All belts, idler tensioner, water pump etc 3000km old. Was running fine after crash - $2000

Gearbox, good condition - $1300

3,000km old exedy heavy duty clutch - $150

Tailshaft - $150

Diff - $150

3" turbo Back exhaust. Bellmouth dump/front pipe into jasma muffler - $400

FMIC Return flow kit. Includes generic fmic with Blitz return flow piping and all clamps/joiners. No holes need to be cut - $300

Front brakes With rotors and pads. Pads still got plenty left. Good condition - $350

Rear Brakes with rotors and pads. Good condition - $150

2 X Starter motors - $50 each

Air Con pump - $50

2 X Gearbox Mounts - $80 each

Rear Axels - $50 pair

Rear bar painted white. Good condition. Appears to have been re-sprayed - $100

Rear bar Reo - $40

Boot lid with Series 1 spoiler - $50

Tail lights - $50 each

undertray stone guard. Has a few small tears - $40

Car mats. Complete set - $50

Drivers side Head light. Off a 4 Door, chrome surround. A little bit yellow. $50

Lots of other parts available. Just let me know what you want and ill get back to you with pics/price.

RB30DET Parts:

Rb25de non vct head from a R32. Head has been cleaned, new valve stem seals, heavy duty springs for turbo application and surface machined flat.

Inlet manifold, injectors and fuel rail, throttle body and all bolts/miscelanious pipes etc - $650

Good Condition S2 RB30 Bottom End, fully assembled. Brought as working motor and stripped head etc off - $75

Rb30 S2 block, disassembled. Includes crank, rods, cradle and block - 6 pack of Bundy

New ACL Duralite cast RB30e pistons and rings, 1mm oversize. Suitable for RB30DET conversion. Will give compression of around 8.3-1. $250

New ACL Duraglide engine bearings. to suit RB30. .25mm oversize. includes rod bearings. $50

RB30 complete engine gasket kit with Headgasket. No sump gasket included - $100

RB26 Oil Pump. Came off R32 GTR. $100

RB20DET Exhaust Manifold. Will bolt to Rb25de head. $40

Will post smaller items at buyers expense. Pickup only for gearbox, engine etc unless you organise everything and pick-up from my house. Contact through here, PM, or message/call me on 0422816780. Cheers, Shane.

Link to comment
https://www.sau.com.au/forums/topic/266117-wrecking-1994-r33-gts-t-victoria/
Share on other sites

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Sorry mate, the boot carpet has been removed from car.

Also have:

R33 GTST Ball Bearing Steel Wheel Highflow - very good conditiong - $900

R33 GTST Stock Series 1 Turbo - Good condition - Has 1 snapped exhaust housing stud - $350

undertray stone guard. Has a few small tears - $40 <--- that the stone guard for underneath the engine.. would you happen to know if it will fit a 32gtr?

also do u have the rear seat belt covers available... the little cover surrounding the seat belts on the rear panel where the seat belts come out from

Can I offer $400 for

Rb25de non vct head from a R32. Head has been cleaned, new valve stem seals, heavy duty springs for turbo application and surface machined flat.

Inlet manifold, injectors and fuel rail, throttle body and all bolts/miscelanious pipes etc - $650

I do not want the inlet manifold, Injectors, throttle body, and bolts \ pipes.

Just the head.

If the fuel rail is the same as the R33 Turbo rail I'll take that though.

Let me know.

after the dash pad (upper part of dash) if it is available and able to be sent. Let me know a price includng estimated delivery and ill see if i can afford it at the moment lol

Pics as well please

Thanks

Worped - 1 Front shock is bent other is good, KYB. Rear shocks are in OK condition, with lowered springs.

Hypnotik - Will take pics now and put em on my photobucket.

Benzino33 - Pics of FMIC are in my photobucket link.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...