Jump to content
SAU Community

Recommended Posts

Hi Gents,

I am new to the forum.

I have a R33 GTST '94 done about 112K. I gave my car for Serive yesterday and was told to change the timing belt.

Does any1 know how many k's can the above model skyline do before it becomes a must to change it?

Even though i have requested for it to be changed, I thought maybe it could be helpfull to have an understanding for me and for others in the forum

Thanks

Harry

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/
Share on other sites

hi there,

Working in an auto parts store as well working side jobsas well as on my own vehicle's i never play the how many miles game. Rather better safe than sorry. good luck,

~skott

so your telling me your gonna change the Timing belt (without any idea or planning/scedule) every 20,000km ....replace just to be safe then sorry?

:P

Hi Gents,

I am new to the forum.

I have a R33 GTST '94 done about 112K. I gave my car for Serive yesterday and was told to change the timing belt.

Does any1 know how many k's can the above model skyline do before it becomes a must to change it?

Even though i have requested for it to be changed, I thought maybe it could be helpfull to have an understanding for me and for others in the forum

Thanks

Harry

it all depends... sometimes rubbers can last longer than others, depending on the ingredients made.

but average recommendations are usually 100,000km.

so if your car hasnt had it done before, its most likely due.

Timing chains usually last a fair bit longer

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4547296
Share on other sites

I bought a s1 r33 with 127000kays on the clock and I suspected the timing belt had never been changed, so i did it + water pump just to be on the safe side.

however now i'm regretting not doing the idler/tensioner pulleys at the same time... apparently if they go it's just as bad! ??

Edited by dnbosiris
Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550092
Share on other sites

if it looks cracked, or teeth missing chips replace

usually they say every 90,000 to 100,000kms

if u dont and it snaps you WILL need new pistons and valves as the 2 meet at a very fast pace

bent valves can also equal cracked valve guides, distorted valve seats, the dust from the chunks taken out of the piston may end up getting picked up in a main bearing journal

alot of machining work and labour hours/costs involved

unless u get lucky and the bent valves do minimal damage, but still $30 + per valve isnt cheap at 24

Edited by Gerg_R31
Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550113
Share on other sites

I bought a s1 r33 with 127000kays on the clock and I suspected the timing belt had never been changed, so i did it + water pump just to be on the safe side.

however now i'm regretting not doing the idler/tensioner pulleys at the same time... apparently if they go it's just as bad! ??

yes i forgot to mention about that one

it is also recommended to replace the idle tensioner puller with the timing belt.. because they are also very old.

well it depends...sometimes its not as bad.....it causes anoyying rattles and squeeks

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4550222
Share on other sites

anyone know what the factory timing settings are for the RB25? am changing my timing belt and having troubles

ok RB25DET timing is as follows:

15 degrees +/- 1 Degrees, 650 +/- 50rpm

ive got a simplified Workshop manual of the R33 Rb25det aroudn 20mgb which shows you how to test it if you need

cheers

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4566372
Share on other sites

so your telling me your gonna change the Timing belt (without any idea or planning/scedule) every 20,000km ....replace just to be safe then sorry?

:woot:

:) should have clarified. i usually do timing on my cars around 60,000 reason: i run the piss out of them. highway runs country side twistie's and if i ever get a chance tracks.

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4567413
Share on other sites

:P should have clarified. i usually do timing on my cars around 60,000 reason: i run the piss out of them. highway runs country side twistie's and if i ever get a chance tracks.

country runs..... well id say definately get them replaced more often to avoid havoc....

as steve irwin said "if ya break down ere........ its ALL OVA!" :happy:

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4568205
Share on other sites

The Timing Belt should have been changed when the car gets to 100,000km's.

Usually they are changed just before the 80,000km's mark.

Best to change it if you don't know if it has been done or not and since you got to 112,000km's, it be a good time to change it.

Link to comment
https://www.sau.com.au/forums/topic/266379-r33-timing-belt/#findComment-4568598
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...