Jump to content
SAU Community

Recommended Posts

I am wrecking my R32 GTR and i am selling the following parts:

(all prices are negotiable on parts)

Work Emotion CR Kai 17 Inch wheels with 90% tyres $2,200

Boot with spoiler $350

HKS coilovers $1000

GTR Brakes slotted cross drilled $1100

R32 GTR doors $250 each or both $400

Cusco GTR strut brace Front and Rear $120 each

GTR cluster $150

HKS dump pipes $500

HKS Front pipe $500

HKS titanium exhaust 4 inch with apexi silencer $1200

Driver Recaro seat $450

GTR passenger Seat $350

GTR rear seats $250

Whole Dash with 2 screw wholes $250

GTR control arms $100 each

GTR G Sensor $300

GTR Cooler $400

GTR ECU $250

GTR Grill $120

GTR steering rack and pin $150

Rear windscreen $150

Petrol Tank $250

Tail Lights $250

Headlights $250

Once again all prices are negotiable.

PM me for photos or any questions

or you can also contact me on 0433-554-014 Musty!

located in melbourne.

Edited by yunus
Link to comment
https://www.sau.com.au/forums/topic/266429-fs-nissan-skyline-gtr-r32-parts/
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...