Jump to content
SAU Community

R33 Gts-t Randomly Stalling While Driving? Pls Help!

Turbz RB-25

By Turbz RB-25,
in Engines & Forced Induction

 Share

Recommended Posts

Turbz RB-25 Experienced

Turbz RB-25

Posted
Posted

Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

Benzino33 Experienced

Benzino33

Posted
Posted
Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

That happened to my 33, I replaced the Idle stepper motor, cleaned the AFM and repositioned the TPS. fixed it.

Good luck

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

CHeers Fellas, will get some carby cleaner tomorrow.

By the way, is it ok if I use degreaser instead of carby cleaner?

The reason I ask is because I got degreaser at home but no carby cleaner. Cheers fellas.

smok74 Community Regular

smok74

Posted
Posted
Hi Fellas,

My car has started to stall randomly while driving and while idleing.

For example, I would be driving my car 10-15 mins, and then it feel like the engine shuts down, then switches back on, the shuts down, switches back on, almost as though the fuel cuts in and out.??

The happens can happen whenever, full throttle, idle, cruising speed, you name it.

It'll happen to me 2-3 times while driving and frankly it's getting quite dangerous when my car stalls on a busy street.

WHen the problem occurs on idle, the rpm drops to almost 0, then bounce back up to 1000, then back down to almost 0, so strange? and it only occurs some times which really puzzles me?

SOmetimes I can go for a 30min drive and it doesn't happen...

DO you fellas have any idea what it might be?

Fuel pump? Coil packs? spark issue? Tune on the car?

ANy help would be great.

Cheers and have a good long w/e

The less residue you leave on the AFM the better - residue (especially oily crap) promotes more sh*t sticking to the wire element .... what I did with mine, flushed the element in the middle of the AFM with a bit of acetone using a little squiter / dropper.... watched all the brown shit come dripping off. Just gotta watch the acetone doesnt come into contact with the wall of the AFM for too long, being plastic, you wouldnt wanna melt it lol its lucky acetone evaporates quickly....

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

Hi fellas,

I got some carby cleaner yesterday and cleaned the wires in the AFM with it.

Alot of brown shit flowed off so it looks brand spankin new now.

It hasn't stalled since and I have a feeling the problem is solved (fingers crossed)

Thanks for all your help fellas, greatly appreciated.

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

Fellas,

The stalling thing happened again yesterday...... I must say but it's improved,

If it was a 8/10 pain in the arse last time, now it's about 2/10.

Nonetheless, it's still doing it??

Should I take out the AFM again and spray it again??

Beelzebub89 Grand Master

Beelzebub89

Posted
Posted

Is your BOV plumb back or atmo? Atmo vented BOVs have been known to cause the same problem. Could also be your Idle Air Control Valve? I think its called. Will probably need cleaning and the idle resetting eiter with the TPS or through the ECU.

When I had my 33 gtst the same thing happened to me. I did the above and it never happened again.

Here is a great tutorial for cleaning the IAC in case you're unsure what to do.

http://www.skylinesaustralia.com/forums/Di...nd-t110431.html

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted
Is your BOV plumb back or atmo? Atmo vented BOVs have been known to cause the same problem. Could also be your Idle Air Control Valve? I think its called. Will probably need cleaning and the idle resetting eiter with the TPS or through the ECU.

When I had my 33 gtst the same thing happened to me. I did the above and it never happened again.

Here is a great tutorial for cleaning the IAC in case you're unsure what to do.

http://www.skylinesaustralia.com/forums/Di...nd-t110431.html

Yeah, I might give the ACC a clean.

It's strange, when idle drops, the voltage on the PFC displays 8.8v, maybe it's something to do with my alternator?

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

What puzzles me is that it can happen at any time, thats why I don't think it's the ACC. The stall can happen even when I am fully on boost, and bang it'll just cut out, then it will cut back in again... It can also randomly just happen on idle...

Maybe it's something to do with the tune???

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted

I've narrowed it down to the following things:

1) Crank Angle Sensor

2) Fuel Pump

3) Harnesses to sensors

4) Ignition Control Module

5) 02 Sensor

6) Coil Packs

7) Spark Plugs

8) AFM

What do you fellas think?

Turbz RB-25 Experienced

Turbz RB-25

Posted
  • Author
Posted
series 1? sounds like the classic power transistor/ignition module is on its way out

It's a series 1, but it has a series 2 engine?

I've also recently placed the RB30 short block on it, with 256 in 264 exh cams, porged pistons, rods etc etc, and a GT35R turbo.

The car is currently on it's run in tune.

sometimes in the middle of driving the engine just stalls... it can usually be just pulled over onto the side of the road and started again.. sometimes it doesnt quite get to the point of stalling but just has an extreme lack of power and no acceleration ability for a few seconds..

I've read a few commodore threads and it seems that their problem is always the CAS...???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Wazmond
      WGNC34 Rear springs

      By Wazmond · Posted

      Try looking at Eibacb/H&R springs Thats what Gary sourced for mine.
    • AdiR34
      Fender flare widths across front/back of car

      By AdiR34 · Posted

      Hey y'all! I'm curious about how y'all go about widebodying your cars. I noticed that when running a square setup, my front wheels are a bit more tucked in than my rear wheels. Not by much, maybe 5-10mm. This leads me to wonder - when I widebody, should I use narrower front flares and wider rear flares? I found a set of 40mm rear flares that I really like, and was thinking of pairing them with some 18mm front flares, but I don't want the car to look strange. How have others done this? Note, I'm in a sedan. Thanks!
    • GTSBoy
      Stagea Front CV Axle Question

      By GTSBoy · Posted

      And if it was anything other than an auto tranny part, it might be a problem. But seeing as all auto trannies belong in the recycling bin, it's fine.
    • GTSBoy
      Stock rb25det neo questions

      By GTSBoy · Posted

      I have an R32 Fenix rad. It is good.
    • dbm7
      Stock rb25det neo questions

      By dbm7 · Posted

      All the schemas I can see, indicate your typical setup of ATF 'cooler' (read: heat exchanger) in the bottom radiator tank..ie; https://nissan.epc-data.com/stagea/wgnc34/5413-rb25det/engine/214/ ...but I can prattle on a bit here. These trannies have a thermistor in the sump ~ the TCU reads this and 1. bumps the line pressure up when the ATF is 'cold' and 2. prevents the TC lockup clutch from operating, until the ATF comes up to minimum operating temp (keeps the ATF 'churning' through the TC so it heats up quicker) -- trigger point is around 55C. In these conditions, the engine coolant temperature rises faster than the ATF temperature, and also helps heat the ATF up, which is why it's best to think of the in radiator tank setup as a heat exchanger ; the heat can flow in both directions... ...with these trannies, the 'hot' ATF comes out the front banjo bolt, flows through the cooler/heat exchanger, and returns to the box  via the rear banjo bolt. This gets a mention, due to the wildly different opinions wrt running auto trans fluid coolers ~ do you bypass the in radiator tank altogether, or put the cooler inline with the in radiator tank system...and then, do you put the additional cooler before of after the in radiator tank system?... ....fact is the nominal engine operating temp (roughly 75C), happens to be the ideal temperature for the ATF used in these trannies as well (no surprises there), so for the in radiator tank system to actually 'cool' the ATF, the ATF temp has to be hotter than that...lets say 100C -- you've got 25C of 'excess' heat, (slowly) pumping into the 75C coolant. This part of the equation changes drastically, when you've got 100C ATF flowing through an air cooled radiator ; you can move a lot more excess heat, faster ~ it is possible to cool the ATF 'too much' as it were...(climate matters a lot)... ...in an 'ideal' setup, what you're really trying to control here, is flash heating of the ATF, primarily produced by the TC interface. In a perfect world, wrt auto trans oil cooling, you want a dedicated trans cooler with builtin thermostatic valving - they exist. These should be run inline and before the in radiator tank system ~ when 'cold' the valving bypasses the fin stack, allowing the ATF to flow direct to the in radiator tank heat exchanger, so it works 'as intended' with helping heat the ATF up. When 'hot' (iirc it was 50C threshold), the valving shuts forcing the ATF through the cooler fin stack, and onto the in radiator tank heat exchanger...and you sort of think of it as a 'thermal conditioner' of sorts...ie; if you did cool your ATF down to 65C, the coolant will add a little heat, otherwise it works as intended... ...the 'hot' ATF coming from the front bango bolt, is instantiated from the TC when in use, so all/any flash heated oil, flows to the fluid-to-air cooler first, and because of the greater heat differential, you can get rid of this heat fast. Just how big (BTU/h) this cooler needs to be to effectively dissipate this TC flash heat, is the charm...too many variables to discuss here, but I just wanted to point out the nitty-gritty of automatic trans fluid coolers ~ they're a different beastie to what most ppl think of when considering an 'oil cooler'... /3.5cents   
×
×
  • Create New...