Jump to content
SAU Community

Recommended Posts

This problems only been starting since i've relocated my amp for my splits to under the drivers seat.

Anyway, I start the car up, drive off, no worries no interference or whine through the speakers what so ever. Pull over, stop, turn the car off, go do whatever, come back say 10 minutes later and crank some tunes and theres now whine in the speakers.

Start the car a few hours later and the whine has since left.

Can anyone see a reason for why this problem only occurs when the car has been running, stopped and then started again???

Thanks

Tim

Link to comment
https://www.sau.com.au/forums/topic/26994-that-dreaded-speaker-whine/
Share on other sites

The whine is actually electrical interfierance being induced into your RCA cable. Move all of your RCA cables far away from any power cables.

Next step is too triple check all earths including the one from the head unit and all amps to ground and from the battery to the bodywork. Make sure they are clean and the paint is rubbed back where they bolt to the bodywork. Make sure they are screwed in tight also check that the insulation on the signal cables isn't worn / cracked / damaged. :rofl:

Have you checked your flux capacitors? or perhaps the warp power relays? .................. Sorry about that! My missus had the same problem in her lancer and it ended up being the amp itself.I moved it back to the original position and it made no difference. i then used the amp on low pass for the sub and the noise was gone, seems to be a filtering problem in the amp. try another amp

Well your fronts need a high pass so they play treble only and your sub/s need low pass for bass only, so if you are running seperate amps and they are hi/lo pass selectable try swapping them to see if the problem goes away. The amps are probably different power ratings but it is just a test so lower your gains. another problem can be that your gains on your amps are too high, you should set your gains as low as poss and your head unit volume to about 90%, as a rule of thumb. I know it can be time consuming but most car audio development is.If you just lower the frequency then you will miss out on high notes and it will sound dull. good luck

yea the fronts hav a high pass on them.

I run jaycar 6.5 inch carbon fibre woofers with JVC cross overs and tweeters on the dash. The amp i use for the splits is a Pioneer 4x50wrms amp (coupla models old now) but still does hte job well.

Gains are set at just on half and the frequency is set on high pass @ 70hertz or there abouts.

I could run the gains higher because im not pushin the limits of the woofers what so ever and they're very efficient.

Is it worth trying another amp to see if its a problem there?

My amps located under the front seat if anyones had any problems there before

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...