Jump to content
SAU Community

Recommended Posts

Hey guys, this is just an Expression of Interest for stripping a R34. 

Things NOT included: Engine, and Manual Gearbox etc (Shehan had dibs on it) :( and ofcoarse the system.

Everything else is up for grabs guys. 

As i said its just an expression of interest to see if it will be worthwhile for me to start ripping the car apart or not. 

Goodies?

Carbon OEM Hood, has some damage on it though. 

Kakimoto Stainless Steal Catback. 

Splitfire Coilpacks 

Xenon Headlights ( Will sell pair unless you can organise for a person to buy a left if your after a right vice versa )

Other than all this, everything else in the car is stock

1999 Model Nissan Skyline 25GT Manual 2 Door. 

White

Shell not for sale. 

Thanks guys. 

And please forgive me if i reply late to PM's or Posts (max delay 12 Hours)

Planning to Strip next month. 

Note: No Bidding on items

Some of these parts will also be on eBay next month and will update the thread once i start to rip it apart and catalogue all the parts available.

MRXTCZ

Link to comment
https://www.sau.com.au/forums/topic/270408-eoi-stripping-r34-25gt/
Share on other sites

  • Replies 62
  • Created
  • Last Reply

Top Posters In This Topic

Just incase people are confused, everything else in the car is up for grabs aswell.

Reason?

I got into an accident, and need to strip the car to make some money back to pay off the loan :(

So, interior panels eg. door panels, seats, floor mats, a/c surround, a/c unit, engine bits and peices just not the whole engine itself.

MRXTCZ

VikZ

Thanks for holding the manual kit for me, but it's up for grabs because I can't take it anymore.

I've no money left to work on the car!

Cheers!

p.s. however i am interested in the front passenger side panel if it's for sale. thanks.

how much for coilpacks? will buy if reasoonable price?

how much for those interior trims around the headunit that always get scratched (if yours arent scratched)

EJD001

Wouldnt have a clue mate, do a search and find out.

OKBANANA

Pm recieved and noted name down for the gear surround, a/c vents and surround and AC unit.

ash_29

If OKBANANA falls through the item is yours, but im pretty sure he wont

imnotwearingpants

Condensor is still available and will let you know a price closer to dismantle date

XKLABA

Number plate lights still available, closer to dismantle date.

SHANE666

No worries dude :P

Manual Conversion kit still for sale!

Keeffy

As Daniel said, cars NA

Natho33

Coilpacks will be let go for $325, less than a year old Splitfires.

Resh

Sorry dude didnt come with the pop up LCD

Hypnotik

I'll have to get back to you on that one.

It is the same as the GTT, just wanna see if they wanna sell drivers and passenger as a pair.

But will let you know asap.

Nushtek

$325

Galla_4

Speedo cluster, i will let you know the price asap

I'd probably PM you :)

For everyone else who has PM'd me, i have replied so check your inboxes.

I've got a list of what people want at home as i am at work right now, and will update that list asap.

I wanna make this as less painful as i can, so i just wanna catalogue the parts, and as soon as you got the money ready i will rip it out and hand it to you :)

MRXTCZ

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...