Jump to content
SAU Community

Recommended Posts

GT-Rs are perhaps best described as "intelligent" 4WD.

Subarus, Lancers, and the like are basically FWD that also feed (constant) drive to the rear wheels.

GT-Rs on the other hand are RWD, and feed some drive to the front wheels when the system detects a need to do so. Not simply when (rear) wheel slip is detected, but also when cornering forces indicate a need for some FWD.

The GTR and GTS4 4WD system is unique to Nissan. There is no centre diff as in most other 4WD systems.

The way it works is that it behaves like a normal RWD most of the time, and under certain conditions, there is a clutch that will feed torque to the front wheels.

I believe the computer that controls the 4WD clutch looks at throttle position, as well as lateral and longitudinal accelerometers, and relative front/rear wheel speeds, and decides how much torque to feed to the front wheels.

It combines awsome straight line traction, but has none of the corner entry understeer of a full time 4WD. It is a very good highly developed system far better than full time 4WD.

Full time 4WD is probably better in mud, dirt, or snow, but the GTR system is more suited to driving on wet or dry sealed roads. It was made to win races, not drive around paddocks.

Hi SIR33, Warspeed covered it pretty well. I would only add that a GTR can have 100% torque to the rear wheels, whereas a front wheel drive based all wheel drive (Sub, Mitsi, VW, Audi etc) can only ever have a maximum of 40% of the engine's torque available to the rear wheels.

Since acceleration and cornering weight transfer is to the rear or diagonal, a GTR will always have higher traction capacity regardless of the suspension set up.

The Evo V111 (some 14 years after the R32 GTR) is the only car that even comes close. Notice "close" not "as good".

Hope that adds to the previous posts

This probably explains why alot of PRO-GTR drag racers are having a hard time getting the right setup with the correct torque split for the 4WD. There are plenty of GTST RWD's running quicker times than their GTR equivalents. This is something that HKS struggle with on their car too, apparently. Because all of those drag RWD suspension and tyre setups go out the window as soon as you try to do it on a 4WD.

Hi Zensoku, a lot of the fast GTST's run drag slicks, whereas a lot of the fast GTR's run street legal radials. There is a huge difference in traction and launch torque handling capacity between a proper drag slick and a radial.

Then there is the weight factor, it takes a lot of extra power to overcome a 250 kg weight handicap.

Hope that adds to the thread

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey everyone. Is there a way I can get the original window sticker (maroney label) for my 1995 R33 GTST? I doubt I’ll be able to ever get it but it’s worth a shot to ask
    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
×
×
  • Create New...