Jump to content
SAU Community

Recommended Posts

So it started out with buying blue replacment LED's for the clusters from 666DAN... but my climate controll lights didnt work, i honestly didnt even know if they were meant to have lights..

took it all appart to find that i had everything needed to turn the existing blown bulbs into blue LED's laying about in my workshop...

oney.jpg

twom.jpg

threet.jpg

fourq.jpg

five.jpg

six.jpg

seven.jpg

eightx.jpg

Looks SWEET now, gonna have a go at getting the LCD backlight blue tomorrow maybe...

I was also thinking about mounting 2 blue LED's inside the air vents so small amounts of blue light comes out of the vents... But on the other hand... That might be too much blue, As the new sterio is gonna be blue theamed aswell.

If i decide to do the Air vent LED's does anyone know the easiest spot to tap into the light circuit?

Link to comment
https://www.sau.com.au/forums/topic/271100-r34-gtt-dash-lights/
Share on other sites

Thats sick! I really want to get mine done, but I've run into so much trouble with it. My last attempt killed one of the LED's. Couldn't find a replacement, so got a whole AC unit replaced.

My original unit was from a series 2 so it had different lights.. now I'm not even sure what LED globes I need from Dan666..... *sigh*

you need to place a resistor in series with the LED to limit the current, other wise it basically shorts out the unit.

i used 2* 180 ohm resistors giving 360ohm total that limited the current to around 25mA whish is the value that these specific LED's create the maximum light output

Slightly off topic but does anyone know how to even out the bright vs dull spots on the dash? I too have recently fitted white multi-angle LED's (from 666DAN) to my R34GTR.

Don't think it's possible man. I've got this kit of 666DAN also and it's the best it can be afaik. I think red LED's make it perfect but.

Here is my setup... I've changed the double DIN HU to Snigle and put a consult display unit underneath.

09072008007Small.jpg

  • 4 weeks later...
  • 11 months later...
So it started out with buying blue replacment LED's for the clusters from 666DAN... but my climate controll lights didnt work, i honestly didnt even know if they were meant to have lights..

took it all appart to find that i had everything needed to turn the existing blown bulbs into blue LED's laying about in my workshop...

oney.jpg

twom.jpg

threet.jpg

fourq.jpg

five.jpg

six.jpg

seven.jpg

eightx.jpg

Looks SWEET now, gonna have a go at getting the LCD backlight blue tomorrow maybe...

I was also thinking about mounting 2 blue LED's inside the air vents so small amounts of blue light comes out of the vents... But on the other hand... That might be too much blue, As the new sterio is gonna be blue theamed aswell.

If i decide to do the Air vent LED's does anyone know the easiest spot to tap into the light circuit?

very nice.... i like it..

You can never have too much blue lol i can barely see out my windscreen at night so many cobalt guages in my face, lol looks maad but i think a lower voltage transformer or somethin might be in order....

Looks cool man.

  • 4 weeks later...

That looks really sick mate. To bad I can't make mine Blue I'm force to do it red. Main reason is the R34 GT T series II has a film over the dash so on well I am happy for you. It turn out really nice and sick :D . Think of blue neon above the pedals and under seat as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...