Jump to content
SAU Community

Recommended Posts

So it started out with buying blue replacment LED's for the clusters from 666DAN... but my climate controll lights didnt work, i honestly didnt even know if they were meant to have lights..

took it all appart to find that i had everything needed to turn the existing blown bulbs into blue LED's laying about in my workshop...

oney.jpg

twom.jpg

threet.jpg

fourq.jpg

five.jpg

six.jpg

seven.jpg

eightx.jpg

Looks SWEET now, gonna have a go at getting the LCD backlight blue tomorrow maybe...

I was also thinking about mounting 2 blue LED's inside the air vents so small amounts of blue light comes out of the vents... But on the other hand... That might be too much blue, As the new sterio is gonna be blue theamed aswell.

If i decide to do the Air vent LED's does anyone know the easiest spot to tap into the light circuit?

Link to comment
https://www.sau.com.au/forums/topic/271100-r34-gtt-dash-lights/
Share on other sites

Thats sick! I really want to get mine done, but I've run into so much trouble with it. My last attempt killed one of the LED's. Couldn't find a replacement, so got a whole AC unit replaced.

My original unit was from a series 2 so it had different lights.. now I'm not even sure what LED globes I need from Dan666..... *sigh*

you need to place a resistor in series with the LED to limit the current, other wise it basically shorts out the unit.

i used 2* 180 ohm resistors giving 360ohm total that limited the current to around 25mA whish is the value that these specific LED's create the maximum light output

Slightly off topic but does anyone know how to even out the bright vs dull spots on the dash? I too have recently fitted white multi-angle LED's (from 666DAN) to my R34GTR.

Don't think it's possible man. I've got this kit of 666DAN also and it's the best it can be afaik. I think red LED's make it perfect but.

Here is my setup... I've changed the double DIN HU to Snigle and put a consult display unit underneath.

09072008007Small.jpg

  • 4 weeks later...
  • 11 months later...
So it started out with buying blue replacment LED's for the clusters from 666DAN... but my climate controll lights didnt work, i honestly didnt even know if they were meant to have lights..

took it all appart to find that i had everything needed to turn the existing blown bulbs into blue LED's laying about in my workshop...

oney.jpg

twom.jpg

threet.jpg

fourq.jpg

five.jpg

six.jpg

seven.jpg

eightx.jpg

Looks SWEET now, gonna have a go at getting the LCD backlight blue tomorrow maybe...

I was also thinking about mounting 2 blue LED's inside the air vents so small amounts of blue light comes out of the vents... But on the other hand... That might be too much blue, As the new sterio is gonna be blue theamed aswell.

If i decide to do the Air vent LED's does anyone know the easiest spot to tap into the light circuit?

very nice.... i like it..

You can never have too much blue lol i can barely see out my windscreen at night so many cobalt guages in my face, lol looks maad but i think a lower voltage transformer or somethin might be in order....

Looks cool man.

  • 4 weeks later...

That looks really sick mate. To bad I can't make mine Blue I'm force to do it red. Main reason is the R34 GT T series II has a film over the dash so on well I am happy for you. It turn out really nice and sick :D . Think of blue neon above the pedals and under seat as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...