Jump to content
SAU Community

Recommended Posts

hey all,

im about to purchase a 100,000k service for my r34 rb25det neo.

now when searching for a full kit for it with bearings and seals and water pump etc...i can find them either for r33 or rb25det.

now will these rb25det or r33 rb25det kits work on my rb25det neo on r34 gtt?

thanks in advance.

Bass.

ok sweet i guess i got my answer.

so the r33 rb25det 100,000k kit and r34 rb25det neo 100,000k service kit are exactly the same and work on both.

so just getting a rb25det kit will work.

only difference i found when doing mine was the water pump, there a few it could be, the first one i got looked ok but it didnt have the enlongated hole at the top where the smallest bolt of the lot go, i cant remember the part number for the one i needed, but all the belt kits are the same i believe, i got my gates kit from CBC bearings through work (mechanics workshop) which came with the blue belt and all the seals and idler and tensioner,

hope i helped lol,

only difference i found when doing mine was the water pump, there a few it could be, the first one i got looked ok but it didnt have the enlongated hole at the top where the smallest bolt of the lot go, i cant remember the part number for the one i needed, but all the belt kits are the same i believe, i got my gates kit from CBC bearings through work (mechanics workshop) which came with the blue belt and all the seals and idler and tensioner,

hope i helped lol,

yeh helped but now im a little confused...is there a variance between r33 rb25det and r34 rb25det neo water pump?

probably. just get the neo kit then it's no dramas?

see, the problem with that is the place im getting it from, eg repco doesnt have anything listen under r34 and only r33 rb25det.

which is why i asked to begin with.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • GTR front looks good. If you don't like it, I'll swap you a rolling shell R33 for it. Give you a fresh base to start with.
    • soon I also prefer the old look. At least I have more clearance for wheels up front now.
    • @PranK I think a few links in the original post need fixing...
    • Has equal chance of cleaning an AFM and f**king an AFM. I think you can work out what happened. When the Hitachi ECU sees the AFM die and goes into the associated limp mode, then it will start and run just fine, because it ignores the AFM and just runs on idle maps that will do what it needs to get it going. But there is no proper load signal, so that's about all it can do. My suggestion? If you don't want to go full aftermaket ECU, then get some R35 GTR AFM cards and some housings to put them in, in the stock location, and Nistune the ECU. Better to do a good upgrade than just replace shitty 40 year old tech with the same 40 year old tech.
    • So my car was recently having trouble starting on initial crank, I would need to feather the gas for it to start up but besides that it would start and run fine. So I clicked the idle air control valve (with throttle body cleaner) and cleaned the MAF sensors (with MAF cleaner). The start up issue was fixed and now the car turns over without the assist of the throttle, but the car is in limp mode and wont rev past 2.5k RPM. From what I understand the IACV would not put the car in limp mode, so I am to believe it is the MAF sensors, but it was running fine before and now I cant get it out of limp mode. I cleaned the MAF made sure the o rings were seated properly. Made sure the cables were plugged in properly, the cables also both read the same voltage. Does anybody know why this is or what could be causing this or how to get it out of limp mode?
×
×
  • Create New...