Jump to content
SAU Community

Recommended Posts

Because of some fool decided to back into the 33 while I'm busy earning my crust,

01082009.jpg

excuse crap pictures. It'll cost you $200 to paint the bumper and grill (Contact Vu @ DT Panels).

So, I'm dropping the price to $10,000 no RWC might include Rego thou. Don't want to hear offers anymore.

If you want more pictures, you may as well come to see the car, cos no point in me wasting my upload to these picture hunters.

Cheers

Grant

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

Still for sale, will look to any offers. As usual all offers are to be go to me through PM.

Cheers

Grant

I want this gone in a month so $10k or near offer.

Frankly, it's cheap for '98 S2 R33, I doubt you'll find one right now.

Cheers

Grant

had a look at this car,

definatley by far the cleanest r33 i have ever seen.

the car drives and feels like a new car!!

free bump and goodluck grant.

had a look at this car,

definatley by far the cleanest r33 i have ever seen.

the car drives and feels like a new car!!

free bump and goodluck grant.

Nathan,

Thanks for kind words.

Feel free to make an offer it might be yours if I'm liking your figures.

Cheers

Grant

Hi all,

Still up for grabs, feel free to make a offer, you might be surprised with my response.

Cheers

Grant

Free Bump! i cant buy this because its turbo : ( but put the car on firesport.com.au (free) / gumtree.com.au (free) / Carsales ($50) / NissanSilvia.com (100 posts) and you should get some interested people, it looks like a nice car!

$9,900 ONO.

B U M P ! ! ! !

I'll look into any reasonable offers as always.

Cheers

Grant

$9,900 ONO.

And zero interest? How is it possible?!

Yes, it's still for sale folks, as usual I'll entertain any offers as long it isn't stupid (keep it in mind that it's insanely cheap for '98 in this colour!).

Cheers

Grant

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...