Jump to content
SAU Community

Recommended Posts

In the past week or so the front right cv boot on the stag has split. As its only just recently happened its making a hell of a mess on the backside of the weel and under and around it all.

How hard are they to change? Ive been told buy Xmetal N15 pulsar boots fit, can anyone confirm this? Can some one give me a how to change it? Its on the RSfour stagea.

Also some tips on doing cheffs 260 stag would be helpfull cos both of his have been gone for a while now and if its a diy well do his soon too ;)

Link to comment
https://www.sau.com.au/forums/topic/271687-changing-cv-outer-boot/
Share on other sites

Ive changed all mine but then realised i didnt to the ties up tight enough and now i have grease all under my car.

Its pretty easy to do, Wheel off, Middle nut out, losen end of drive shaft and take it out. A rattle gun is very handy to use also.

Also once u got it off take it to the C.V joint and drive shaft place in edwardstown, same rd as doyle crash but closer to south rd. They are roughly $15bucks each with grease.

Could work. Might be able to leave the rotor on and handbrake and undo it that way. Only one way to find out i guess.

Mines 4wd to, shouldnt make any difference. Just do the end ties on the boots up tight.

shit never really looked at that its a gt -4 ! lol sorry mate!

Hand break wont d oa thing cos its the fronts :P ... just get someone to stamp on the pedal :cheers:

havnt seen you out it a while how ya been anyway?

mayeb i will have a go myself... thought it could be tricky... gues I shouild be able to tackle most things after taking both turbos of adams 26! f**k doing that ever again.

if the boot has split and most of the grease is out DONT just put another boot on it chances are water/grime has already got into the joint and will still stuff up, better of hitting up S.A suspension in pooraka and getting a bearing kit done with new boot! just not worth all the effort for it to stuff up in a couple months!

yeah ive got some prices and cheapest by far is 85 at some place down in Lonsdale. Not close but its a fair bit cheaper.

If lukes done all his 4 ill have a look at it tomorrow morning and see what i think.

my front left is going.

boostworx will do it for $120

actually booking in now

  • 1 year later...

Digging up an old thread here. I've done the rightfront drive shaft inner boot on my R33 GTR. I rang SA suspension and they only had a part number for an R32. My question...... Do the R32 and R33 GTR's use the same boot. If anyone knows for sure and it is the same, I can buy the boot and do the job over Easter, otherwise I have to take the shaft out to try and find a match.

Thanks.

  • 2 years later...

Hi, i know this is an old thread, but i thought id try m luck.

I have recently had a split boot on my rear cv outer joint.

I have new boots and was gonna do both sides my self.

How hard is the job?

My car is a skyline R34 GTT

Any answers would be great, thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
    • If you are keen, have a look at my build thread. Car is for sale for the right money or straight swap for a F80 M3 LCI.
    • Welcome mate.  No point in over thinking it, buying any one of those cars you mentioned is not a smart or logical choice with the availability of many "better" (re price to performance) cars available to you.  The heart wants what the heart wants, buy whatever it leads you too.
    • Hey everyone! Im so grateful to be apart of this community and ill do my best to be apart of this. Firstly, i'm not disclosing my real name due to in real life circumstances surrounding my privacy and public image (sorry lol) Secondly, The only thing personal I am willing to share is that I'm from Sydney and a descendant of one of Sydneys largest mortgage firms. I got gifted my first ever car, a 2022 Porsche Cayenne and I love it to death. Ive been driving it for about 5 or 6 months now and honestly Im so grateful for my parents for gifting me this vehicle. However recently I've been working my ass off to afford my second car (which I need help deciding soooooo community help me out please?). Once decided, im planning to try modify it myself. Recent I've been thinking about getting a Skyline, particularly a 25GT or GT-V, yes I know overrated as hell, but I'm also considering a Chaser which I recently came to love. However my dream is to one day own a 180SX (So hard to find clean versions and im not really into importing).  Lastly before I send this off, I want to apologize if I sound tacky or pretentious. I try not to and want to genuinely learn from everyone and anyone. (Im no expert in this area) Thanks for reading!
    • I've got three stashed away but it's starting to get silly with the prices 
×
×
  • Create New...