Jump to content
SAU Community

Recommended Posts

does anyone haved relocate in the trunk or in the car the abs system?? i haved did some searches and i find just 2 pic of a guy that put it in the trunk so any information about that will be great thanks!

You could relocate it into a towed trailer as long as you know what you're doing.

But the real question is why?

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4621578
Share on other sites

does anyone haved relocate in the trunk or in the car the abs system?? i haved did some searches and i find just 2 pic of a guy that put it in the trunk so any information about that will be great thanks!

You can move it but its not a simple thing to do. You would need to go to a brake place and get them to re-run the hard lines from the ABS to the brakes. You would also need to modify/extend the electrical connections to it too.

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4623595
Share on other sites

If it's weight you're after go the battery definately.

As for placing a breather in the ABS position, Nismo make a kit that is compatible with the 32R (pt# 11830-RSR25)...naturally it's way exe. You could get someone to fab the can and build it yourself for next to nothing

oir-sep.jpg

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4624675
Share on other sites

battery is already in the trunk but i dont want to put my cacth can there because i dont want the 2 long pipe that goes from the back to the front... but i see nismo catch can will possibly be a solution but i want to know if a small can like this fill up rapidly??

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4628192
Share on other sites

i want to put my catch can there but i want to keep the abs cause if i pass an inspection i will be illegal an i dont want to reput my abs just for that plus its make the engine bay much more cleaner

R32GTR's were available without ABS, in fact none of the N1 (race) versions had ABS. So no ABS is not a rego issue, they don't have to have it.

Cheers

Gary

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4630479
Share on other sites

2 of the race cars down in tassie have the abs pump in the rear passenger footwell (behind where the passenger seat is). one is a gts-t and one is a 200sxr. I only have spoken to one, and he said the braked performed just how they should do.

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4630490
Share on other sites

i already know about r32gtr n1 with no abs and its have a very nice look under the hood and i dont know what are your rule in australia but im in quebec,canada and we dont have the right to uninstall any safety device like if you have a 6 point harness you have to keep your oem belt to be legal its f**king shit but its that.. samething for abs also, i want to know if i extend the electrical harness of abs if it can alter the signal because if you put an extra lenght of wire it create some resistance so the voltage of the signal is not the same??? i hear a guy that have relocate its fusebox an some bug appear... he put back a new harness and no problem so is it that?? im ok with the line but its the electrical side that im not sure with... loool sorry for my english im a f**king frenchmen like they say lool

thanks!

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4630560
Share on other sites

Well you would be making the harness shorter as the abs ecu is in the boot, so that shouldn't be a problem. You could even keep it the same lenth, and just wind the excess up in the boot if your that worried about it.

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4630579
Share on other sites

i already know about r32gtr n1 with no abs and its have a very nice look under the hood and i dont know what are your rule in australia but im in quebec,canada and we dont have the right to uninstall any safety device like if you have a 6 point harness you have to keep your oem belt to be legal its f**king shit but its that.. samething for abs also, i want to know if i extend the electrical harness of abs if it can alter the signal because if you put an extra lenght of wire it create some resistance so the voltage of the signal is not the same??? i hear a guy that have relocate its fusebox an some bug appear... he put back a new harness and no problem so is it that?? im ok with the line but its the electrical side that im not sure with... loool sorry for my english im a f**king frenchmen like they say lool

thanks!

How do they know your particular car came with ABS?

Cheers

Gary

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4631112
Share on other sites

do you enjoy wasting money,

you can move it but its a waste of time spend 600 bucks on a coustom catch can with gold plated rivets and you will still have change compared to moving the abs.

there are plenty of places for catch cans in the engin bay .

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4631748
Share on other sites

Well you would be making the harness shorter as the abs ecu is in the boot, so that shouldn't be a problem. You could even keep it the same lenth, and just wind the excess up in the boot if your that worried about it.

[/quote

i like your idea and sk i dont where they see it but they know..

Link to comment
https://www.sau.com.au/forums/topic/272116-abs-relocation/#findComment-4633064
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...