Jump to content
SAU Community

Recommended Posts

what are legal positions for front number plate? after getting my car resprayed i want to mount front number plate on the side but dont know which side?

i already had cops trying to defect me for number plate angle and only 2 screws coz they couldnt find anything else, so i wanna be sure before i drill any holes in freshly sprayed front bar.

Link to comment
https://www.sau.com.au/forums/topic/272186-number-plate-position/
Share on other sites

i dunno whats legal but i have mine mounted on the left and ive had many cops look at my car and not say anything about it :rofl:

i think its got to be about 100mm off the ground to be legal or something , might have to call regency up mate

passenger side. only reason i chose that side is a lot of cars that come from the factory with offset plates, have em on that side (ie alpha romeo).

dont think they are to fussed on which side they are on. but it would make sense to have them on the drives side though, that way on-coming traffic can see it with ease

OK..

i was pulled up by a cop at a car park on one of kell's cruises,

i had it on the passenger side, right down the bottom of the bar.

she didnt mind it being on the side, or on an angle, but said it had to be ATLEAST 30cm off the ground.

first hand info right there.

I'm not sure about the ruling in SA, but in Vic it must be legible when viewed from a 45-degree angle from either side of the car.

Its about 20 degrees maximum in the official transport SA guidelines but like craig said, they're more concerned about visibility and height - I've never had any issues with my plate, it went thru regency fine with the relocation kit and that has around a 10 degree angle

-D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Is that the blue one rpm?  
    • Update 2: Today I'm f**king pissed. Some of you probably saw my thread that I opened shortly after joining this forum, "urgently need expert/experienced opinion", in which I discussed the possibility of a porous RB26 engine block which I also found hard to believe. Currently both turbos are out since the shitty braided line that was installed by whoever fitted the GT28 turbos leaked oil onto the exhaust. Today while working on the cam covers to put new gaskets and half moons in, I cleaned the side of the engine block with brake cleaner. Some time later I saw that it was still glistening with oil or coolant so I dried that off. But it was wet again shortly after. Verdict: I'm royally screwed. What you can see here (hopefully, despite shit resolution), circled in red, is a crack above the turbo oil feed. Extent is a few cm long and basically goes from #3 cylinder wall to #4 cylinder wall. It slowly lets coolant through, even without any pressure behind it. I am absolutely dumbfounded as to how this crack even formed, especially since it isn't along the cylinder as it usually is but rather a horizontal crack. Probably a few cm in length. Not sure on how to deal with this issue right now. Most likely, the only true fix is a new engine block, and even a relatively well done temporary fix requires at least a full engine teardown. Neither of those really fit my timetable right now, the car has been in my buddy's garage long enough as it is. I'm open to suggestions, but I'll be looking into ordering a new 05U block soon so I have one ready for the coming year, or whenever the current block inevitably fails fully. (Most likely once the crack reaches one of the frost plugs) I think it'd be a waste of money and time to rebuild the engine with this block. Oh and I found a rust hole on the side pocket of the trunk, which someone covered up with sealant goop, a piece of number plate and bodywork filler. Fun times. So far for every issue we fix we just find a new one that is arguably worse.
    • I have not found this no. I put one back on a couple days ago with no drama. I agree they are tight, but no need to remove anything. 
    • That is gates blue racing belt
    • Anyone found gates blue racing to be extremely tight/ almost impossible to install without moving the exhaust gear
×
×
  • Create New...