Jump to content
SAU Community

Recommended Posts

I was faced with the same problem on the R33GTST when I had the 450 bhp target on pump 98, the rediculous cost of straight swap injectors made me search for another answer. The best solutiion I could come up with was a GReddy copy inlet manifold, a set of GTR top feed injectors and a GTR fuel rail with a Nismo adjustable fuel pressure regulator to push the injectors the fraction more necessary (440 to 450 bhp). Since I already had a set of standard GTR injectors and a fuel rail, the only cost was $400 for the manifold and FPR plus making up a resistor pack was no big deal for me.

That's not actually what the car has, due to the availability of E85 I decided the GTR injectors weren't going to be big enough, so I used 550 cc injectors (13B turbo) which are high impedance so I didn't need to use the resistor pack. Waste not want not, I used the resistor pack on the R32GTST with its 1000 cc Rochester injectors as they are low impedance.

Cheers

Gary

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4646536
Share on other sites

On the topic of Injectors

How are those 1000cc Rochester and 855 Bosch injectors you see on ebay for cheap?

my understanding is they need a 14mm fuel rail and connectors? (on GTR so same low impendance)

they seem alot cheaper then sard/greddy/hks etc

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4647325
Share on other sites

Ye thats beccause as you said, they dont bolt in.

probably also need new injector plugs and so on, which end of the day cost vs effort vs time... the jap direct replacement stuff probably comes close, certainly wins in the speed stakes which on workshop rates can save you money :mad:

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4648236
Share on other sites

So really you're better off changing to a GREDDY type intake mani, and GT-R rail + injectors rather than just using drop in replacements for the RB25DET pricewise? I'm finding that the stock ones seem to be hitting awfully close to full cycle sometimes (had a light come up on the display once to indicate max duty when setting up EBC with continued 18psi runs), and are now looking at replacing the injectors rather than be dodgy and use a FPR.

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4648257
Share on other sites

Just to clarify, the RB26 and RB25 fuel rails all bolt up to the GReddy RB25 intake manifold. The difference is the injectors / FPR. I need to clarify as im doing a 25/30 using a greddy manifold and just need to open up my options for fuel rail, injectors and fpr.

Many thanks.

Edited by Stargate
Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4649018
Share on other sites

Yes the stock rb25 fuel rail will bolt onto the rb25 Greddy manifold

aftermarket rb26 fuel rails also bolt up to the greddy manifold

im sure the stock one does too, but changing from hi impendence injectors to low you need the 26 resistor pack?

aftermarket rails also come in different sizes

most common being 10.5 and 11mm

Edited by R32 Driver
Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4653532
Share on other sites

I am in the process of testing 13 different types of JECS injectors (dont ask me where i got them from) i work in the automotive industry. these are all side feed and are the right impeadence for r32 and r33 gtst ecu's

they bolt right into the rail of an rb25 and even fit the plugs. once finished I should have availability of 440, 600 and 790cc injectors based on a fuel pressure of 42psi.

the problem with this is I have had to BUILD my own flow testing bench and calibrate it against another machine. this is due to most commercial machines do not have toe ability to test 6 800cc side feed injectors. I went a bit overboard and buit a bit of a monster and in the end spent more than a commercial machine costs building it but it is one hell of a machine.

once this is all done I am hoping to have sets of injectors available for less than $400 perhaps even $300 if i can get all the parts needed for the right price. I was sick of paying stupid amounts for aftermarket products that are O.E. hopefully I will be able to recoup some of the cost by selling a few sets.

I still need to do a bit more testing before i am happy to sell them to people but so far I have a factory idle with bolt in 790cc injectors and excellent atomisation. they will flow enough for 450rwkw safely. that should be enough for almost anyone.

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4653666
Share on other sites

I am in the process of testing 13 different types of JECS injectors (dont ask me where i got them from) i work in the automotive industry. these are all side feed and are the right impeadence for r32 and r33 gtst ecu's

they bolt right into the rail of an rb25 and even fit the plugs. once finished I should have availability of 440, 600 and 790cc injectors based on a fuel pressure of 42psi.

the problem with this is I have had to BUILD my own flow testing bench and calibrate it against another machine. this is due to most commercial machines do not have toe ability to test 6 800cc side feed injectors. I went a bit overboard and buit a bit of a monster and in the end spent more than a commercial machine costs building it but it is one hell of a machine.

once this is all done I am hoping to have sets of injectors available for less than $400 perhaps even $300 if i can get all the parts needed for the right price. I was sick of paying stupid amounts for aftermarket products that are O.E. hopefully I will be able to recoup some of the cost by selling a few sets.

I still need to do a bit more testing before i am happy to sell them to people but so far I have a factory idle with bolt in 790cc injectors and excellent atomisation. they will flow enough for 450rwkw safely. that should be enough for almost anyone.

any chance of something that would fit Neo rails?

Link to comment
https://www.sau.com.au/forums/topic/272690-injectors/#findComment-4653741
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...