Jump to content
SAU Community

Recommended Posts

I have access to 5 Nitto oil pumps for RB engines. These pumps are individually assembled, set-up and tested. They use the latest generation world class materials.

Pumps are being sourced locally through Croydon Racing Developments and are now used in all of their big engines.

price is $1250 delivered. This is a huge saving over the comparable Japanese items.

please register below.

Link to comment
https://www.sau.com.au/forums/topic/274126-nitto-rb-series-oil-pumps/
Share on other sites

Paul, please confirm the start and finish date for this group buy, as well as the name of the business supplying the pumps.

Thanks.

look at the above post it clearly states CRD are the supplier. Lets say group buy is open for 8 weeks from date of original post. :P

I have access to 5 Nitto oil pumps for RB engines. These pumps are individually assembled, set-up and tested. They use the latest generation world class materials.

Pumps are being sourced locally through Croydon Racing Developments and are now used in all of their big engines.

price is $1250 delivered. This is a huge saving over the comparable Japanese items.

please register below.

Do you have any more info about them?

//Peter

Do you have any more info about them?

//Peter

This place has a few photos up and a little info, not much, but you get the idea. It would be my choice of pump..

http://www.tweakit.net/shop/product_info.p...roducts_id=7204

RB SERIES HIGH VOLUME OIL PUMP

The NITTO RB series high volume oil pump is a high quality and performance aftermarket oil pump that will suit Nissan RB20, RB25, RB26 and RB30 engines. Oil flow and pressure is dramatically increased over that of the factory oil pump which is critical in modified engines for reliability of the lubrication system. Failure of this system is the “achilles heel” of the Nissan RB series engine even on lightly tuned examples and accounts for a high percentage of engine failures.

Factory and factory based oil pumps are highly prone to oil pump gear failure in modified engines due to the quality of the cheaper mass produced material used for the manufacture of the gears. Oil pump gear failure will result in indefinite engine damage. For this reason EN26 ball bearing steel is utilised for the manufacture of NITTO RB series high volume oil pump gears which are superior in strength and durability to that of both factory and its competitor’s oil pump gears.

NITTO RB series oil pumps are supplied pre-inspected, blue printed, assembled and cleaned to enable direct installation strait onto your engine and assure total confidence.

Detailed list of components:

Gears:

Material: EN26 ball bearing steel

Housing:

Quality alloy casting

Technical Specification:

Pressure relief valve crack off (dual springs): 120 psi *

Pressure relief valve crack off (outer spring only): 75 psi *

FLOW (LITRES / MIN)

ENGINE RPM

FACTORY OIL PUMP

NITTO HIGH VOLUME OIL PUMP

750

4.6

6.5

2200

15.3

20.2

7000

46.5

64.8

has mine been sent or waiting to sell all 5??

did u recieve my payment???

no yours has arrived and will be sent to you tomm.

you have pm

thanks

Edited by DiRTgarage
  • 4 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...