Jump to content
SAU Community

Clicking Sound From Wheels On Hard Turning

09GTR

By 09GTR,
in R35 GTR

 Share

Recommended Posts

09GTR Collaborator

09GTR

Posted
Posted

A friend of mine told me that at about 3000 kms his R35 started "clicking" loudly from the wheels on hard cornering. Well, on que, at almost exactly 3000 kms mine has started doing the exact same thing - and I havent even driven the car that hard. Sounds break-related. Does anyone else have this problem, or a remedy?

sickskyline Rookie

sickskyline

Posted
Posted
A friend of mine told me that at about 3000 kms his R35 started "clicking" loudly from the wheels on hard cornering. Well, on que, at almost exactly 3000 kms mine has started doing the exact same thing - and I havent even driven the car that hard. Sounds break-related. Does anyone else have this problem, or a remedy?

It sounds like the ball joints under pressure are you turning at full lock when this clicking sound happens. :(

09GTR Collaborator

09GTR

Posted
  • Author
Posted

Duncan, thanks for the link, it looks like they have it sussed out and are awaiting a fix for it. Also looks like a lot of GTRs have the problem. I'll take the info you sent me to Crawfords.

Cheers.

Gibbo_R35 Community Regular

Gibbo_R35

Posted
Posted (edited)

I had exactly the same noise when turning right at higher speeds, a couple of runs through Galston Gorge revealed this. The strange thing though is that the noise is now gone, I do not know what has changed.

On a side note just for readers information, there is a rattle noise from the front of the car when I go over a bump, this combined with with clicking when turning raised some flags. Anyhow after some inspections I found the issue for the rattle when going over the bumps, the top steel pin that goes through the caliper is a floating pin and vibrates and rattles.

I am curious who else has seen this.

Cheers

post-57732-1244937324_thumb.png

Edited by Gibbo_R35
09GTR Collaborator

09GTR

Posted
  • Author
Posted
I had exactly the same noise when turning right at higher speeds, a couple of runs through Galston Gorge revealed this. The strange thing though is that the noise is now gone, I do not know what has changed.

On a side note just for readers information, there is a rattle noise from the front of the car when I go over a bump, this combined with with clicking when turning raised some flags. Anyhow after some inspections I found the issue for the rattle when going over the bumps, the top steel pin that goes through the caliper is a floating pin and vibrates and rattles.

I am curious who else has seen this.

Cheers

Thanks Gibbo, interestingly the noise has not reappeared today on my car either. I havent had the rattle noise.

  • 7 months later...
LSX-438 Mentor

LSX-438

Posted
Posted

I've had this clicking noise surface recently.

It seems the USA boys thinks it is one of these:

1. Missing top pad retaining SPRING (the front calipers usually only have one of these)

2. Rattling pad retaining PIN (as mentioned above)

3. Loose tie rod ends

Did you guys resolve this and/or had it resurface?

fungoolie Community Regular

fungoolie

Posted
Posted

I'll add another one to this. I had the problem appear at around 9000 kms and took it in to Nissan. They said they spoke to Japan and diagnosed it as the fully floating rotor making noise because some anti-seize grease they use between it and the hub had washed out. Anyway they replaced it with a non genuine compound as they didn't have the proper stuff in stock and it lasted a week before the noise reappeared. I'm now on 17,000 kms and about to take it back in as I want that looked at as well as my MFD backlight dying on hot days as well as my interior mirror developing a droop on 40+ days after a day in the sun. I'll see if I have that retaining clip installed tonight and suggest that to them as well the tie rod end when I drop it off this week.

I've had this clicking noise surface recently.

It seems the USA boys thinks it is one of these:

1. Missing top pad retaining SPRING (the front calipers usually only have one of these)

2. Rattling pad retaining PIN (as mentioned above)

3. Loose tie rod ends

Did you guys resolve this and/or had it resurface?

fungoolie Community Regular

fungoolie

Posted
Posted

No top pin anti rattle spring found and that upper pin clicks loudly with a similar sound when I push it side to side. To me it seems the obvious fault/problem. See what Nissan thinks...

LSX-438 Mentor

LSX-438

Posted
Posted

Out of interest i put the car up on stands today, and started t up, put it in gear, bit of throttle, turned full lock (left) and no clicking. So when there is no load on the wheels/suspension i dont get the clicking. Might be a clue... anyway i am going to be taking a closer look over the next few days, just ran out of time today.

fungoolie Community Regular

fungoolie

Posted
Posted
I'm no R35 mechanic (just a normal mechanic anyway :down: ) but a click on full lock is normally worn out CV joints. Has anyone actually got to the bottom of this problem yet?

Yes I can see how you would think that, that was my first suspicion as well but the Nissan Tech had a listen and said it definitely didn't sound like CVs. Plus a fiddle with the brakes and it gets better immediately, albeit temporarily in my case. In fact last night by just playing with the pins and moving them back and forth stopped the problem for about the first 20 mins of this morning's drive before they must've shifted again to their favourite rattling position! The sound from the pin when manually rattled does sound a lot like the click you hear whilst driving and the US guys seem to be convinced that the anti rattle spring omission seems to be the problem..

Kujotk Grand Master

Kujotk

Posted
Posted

i havent read all the posts or the links, but ive had cars with similar issues (NOT R35) and with these cars its either a Faulty brake assembly (uneven ware on one pad), CV joints or a worn/broken wheel bearing..... ive eevn had a car with diff probs making a similar sound but for the rear of the car, and even the power steering...

LSX-438 Mentor

LSX-438

Posted
Posted (edited)

Like i was saying i was getting the clicking, just turning left. Put the car up on stands and with no load on the wheel, and with wheel turning...no ticking. Anyway i had to replace the pads anyway... So i did remove the pad pins and re-install again. Also the tie rod end nut was not very tight, i could tighten a couple of turns. After i did all this and put it all back together the noise was gone! So unfortunately i can't isolate where the noise was coming from exactly. It's either the tie rod or something related to the caliper. It doesnt look like a stuffed CV. Interestingly also, i noticed the tie rod end cotter pin can rattle around, when you move it with your finger it sounds a hell of a lot like the noise in question.... tick tick tick... so i tapped it down tighter. Anyway the noise is totally gone for now i will let you know if it comes back. Relieved it's not a CV.

Edited by LSX-438
fungoolie Community Regular

fungoolie

Posted
Posted

Was informed by Main North Nissan today that they have three owners with the clicking problem at the moment and are narrowing down the cause on a test mule. So they told me to hold off bringing in mine till they sort it out. I told them about the info available on the US forums regarding missing top anti rattle springs and loose tie rod ends and it appeared to be news to them! We'll see if they can come up with a permanent fix soon.

roadworia Collaborator

roadworia

Posted
Posted

we get a lot of nissans with similar noises. found that the cv shaft spline is dry causing the clickling. i removed cv, lubed spline and retorque the hub nut properly and noise goes away...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Hi from Canada, Both of my calipers are starting to fail. My car is a 2005 M35 Stagea ARX and I can't seem to find any parts or any cross reference caliper that would fit my car. Is there a company or a similar caliper that would fit and I could replace the OEM one. Or if anyone knows where I can find a new OEM. Any help is very appreciated. Let me know!
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Maf is a question mark but TPS  I have set at 0.47, the fact that I’m getting proper voltage range out of it with the key on leads me to believe it’s functioning properly. I’m getting proper voltages on basically everything. I still need to look up voltage ranges for z32 maf and test that 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Honestly no not at all, but it’s a very basic tune, it’s stock injectors q45 tps and z32 maf. Other than that it’s a completely stock base map. The file is from nistune and from my understanding if it was tune related I would be able to unplug maf and tps and it would still start even if it was a really shitty start. I have tried starting it with coolant temp, maf, and tps unplugged none of those 3 togethor or individually changes anything 
    • Matt Z
      SAU NSW - Bathurst Run 2025

      By Matt Z · Posted

      🏆 Skyline Supremacy Meets Mount Panorama Magic 🏆 Join SAU NSW as we take the long way to Bathurst, the home of GTR greatness. Saturday 30th August 2025 7:00AM Meeting Hanna Park North Richmond 7:30AM Departure Cruise Via Bells of Line Road 9:00AM Arrival to Stop 1: Golden Poplars Meadow Flat 9:45AM Arrival to Final Destination: Mount Panorama Motor Racing Circuit Meet Location: Hanna Park North Richmond Stop 1: Golden Poplars Meadow Flat Final Destination: Mount Panorama Motor Racing Circuit   *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • soviet_merlin
      My BMW E39 528i touring

      By soviet_merlin · Posted

      What does it look like with highway driving? And yes, I had a similar thought as Duncan. It looks quite similar in my Stagea and I have made myself accept it as normal. Might have to look into it some day   Highway gets as low as 10l/100km on my end so I'm not as worried about it being a mechanical issue. More likely just the tune on the haltech.
×
×
  • Create New...