Jump to content
SAU Community

Nissan Skyline R32 Gtr 500+hp

r32gtrskyline
 Share

Recommended Posts

  • 3 weeks later...
  • 4 weeks later...
  • 2 weeks later...
PWND Grand Master

PWND

Posted
Posted

can you be more specific about the "built engine"

built as in it has forged internals, in which case a list of parts used and preferrably the name of the builder would go a long way

or is it built, as in "nissan built it back in 1992"

GRKGTR Experienced

GRKGTR

Posted
Posted

The motor was obviously built in Japan as you can see from the setup.. No disrespect to the owner but he would not have a clue on the engine internals as it hasnt been opened.

PWND Grand Master

PWND

Posted
Posted
The motor was obviously built in Japan as you can see from the setup.. No disrespect to the owner but he would not have a clue on the engine internals as it hasnt been opened.

my skyline was obviously built in japan too. as was every other one. i am not sure why you are answering whether the owner knows what the internals are. if he doesn't know, then the engine should not be advertised as a built engine. if he does, could he please share the information.

  • 1 month later...
  • 4 weeks later...
NoFX_Hardcore Proficient

NoFX_Hardcore

Posted
Posted

Obviously doesn't know and is trying to hide it since he has been asked so many times.

To the owner: harden the f**k up and just list details of the engine "build". What pistons/rods etc were used and who "built" it? You are never going to sell it without these key details.

r32gtrskyline Rookie

r32gtrskyline

Posted
  • Author
Posted
Obviously doesn't know and is trying to hide it since he has been asked so many times.

To the owner: harden the f**k up and just list details of the engine "build". What pistons/rods etc were used and who "built" it? You are never going to sell it without these key details.

Why do you bother to reply to something when you arent interested. You are just being a f**k wit. As I have said to others who pm me about the car I am not the owner and to contact the owner if they wanted to know more about the car.

PWND Grand Master

PWND

Posted
Posted

Might want to check the classifieds rules

6. No posting on behalf of others! - If your mates want to advertise their parts here on SAU, tell them to register - If you dont own it, dont post it for sale.
R31Nismoid Grand Master

R31Nismoid

Posted
Posted
Why do you bother to reply to something when you arent interested. You are just being a f**k wit. As I have said to others who pm me about the car I am not the owner and to contact the owner if they wanted to know more about the car.

Well tell the owner to register.

Thread edited and locked.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      Whoops!
    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      Literally looks like direct port nitrous haha
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      They are in fact just nozzles. They are there only to produce a spray pattern and limit flow. The injector itself is what I use to control flow to the 7x nozzles. My old system had no injector and only PWM the pump. This lead to a lot of inconsistencies, and poor atomization at low pressure when the pump was ramping up. 
    • Dose Pipe Sutututu
      UniClutch

      By Dose Pipe Sutututu · Posted

      Jim Roulette 
×
×
  • Create New...