Jump to content
SAU Community

R33 Monster- Drift Or Circut


Recommended Posts

Hey, due to unforseen circumstances..........gota sell up, cant keep this car around unfortunately as much as i want too......

PM if serious - NO SWAPS

Call Jarrod - 0433663833, priced to go as soon as possible. Is one of the best cars out there, needs a new home.....

ENGINE: 356 rwkw @ 1.4bar

-RB27DET-

Just clocked 50,000 original K's, done much much less since re-build

Nismo N1 bottom end

Nismo N1 RB26 crank

Nismo N1 RB26 oversized forged pistons

Nismo N1 RB26 conrods

RB26 waterpump

Tomei Adj Cam (inlet)

HKS Adj Cam (exhaust)

HKS step 3 cams 272 deg

Trust Timing Belt

Apexi RX-6 turbo (ISAMU SERIES)

Custom Manifold

3inch Dump Pipe

50mm Apexi external gate and screamer

Greddy type r BOV (race spring)

Greddy Plenum

800cc injectors

Q45 infiniti throttle body 90mm

BTR Custom intercooler 650x300x140mm

BTR Custom radiator

BTR Custom oil cooler

3inch piping to turbo and inlet

Blitz SUS pod with titanium inlet

SUSPENSION:

Crux coilovers

S.W.I.F.T springs 14kg front, 12kg rear

IKEYA FORMULA lower control arms (brand new)

IKEYA FORMULA castor rods (brand new)

GTR rear strut brace

Cusco front strut brace

BREMBO brakes - upgraded front rotors + endless circuit pads and spares

FUEL SYSTEM

full external fuel system running to an internal fuel tank

650hp rated external fuel pump

2.5ltr swirl pot

EXTERIOUR/INTERIOUR

Trust/Gracer front bar X2

BN sideskirts

BN rear bar

Velo Apex race seat - fixed back

Hydraulic handbrake

Full Cage - 10point

Harness

All the important gauges to keep an eye on everything

+ many many many more things, cant remember it all

will not seperate.

$18000 ONO happy to ship at buyers expence

post-34936-1245218520_thumb.jpg

post-34936-1245218639_thumb.jpg

post-34936-1245218776_thumb.jpg

post-34936-1245219219_thumb.jpg

post-34936-1245222476_thumb.jpg

post-34936-1245222693_thumb.jpg

post-34936-1245222833_thumb.jpg

Link to comment
Share on other sites

it looks like a 25 cause it is a 25?

head and block

bottom end is all rb26 however

owner wont have receipts as it came from Japan already built

I use to work at the shop that bought the car in Terry Vahoumis refused to dirve it back from the docks

on the trade plate as it was to hairy for the street give you an idea how tough the car is and that was running

only running 1 bar

over size 26 pistons make it bigger c.c than rb26's standard displacement wanna get technical its

2568cc + what every 1mm oversize piston make it

or it has one of these cranks in it http://www.nismo.co.jp/en/products/competi...e/rb26dett.html

either way auction report stated 2.7lt

all I know is it it halls arse and Ive recommended three other 25 engine be built to the same Jap style spec's

all of which rev crazy compared to a stock 25 capacity built motor

Edited by 1400r
Link to comment
Share on other sites

hey mate, absolutely awesome car. And we respect how you havn't been a dropkick and changed the rb25 covers to rb26 covers on the head.

as for the people upping the engine capacity, it would be just a fraction under 2.7L if you can do any sort of maths at all.

good luck with the sale mate. very nice car.

Link to comment
Share on other sites

it looks like a 25 cause it is a 25?

head and block

bottom end is all rb26 however

owner wont have receipts as it came from Japan already built

I use to work at the shop that bought the car in Terry Vahoumis refused to dirve it back from the docks

on the trade plate as it was to hairy for the street give you an idea how tough the car is and that was running

only running 1 bar

over size 26 pistons make it bigger c.c than rb26's standard displacement wanna get technical its

2568cc + what every 1mm oversize piston make it

or it has one of these cranks in it http://www.nismo.co.jp/en/products/competi...e/rb26dett.html

either way auction report stated 2.7lt

all I know is it it halls arse and Ive recommended three other 25 engine be built to the same Jap style spec's

all of which rev crazy compared to a stock 25 capacity built motor

not to mention, ryan, that this car is one of THE most intense sounding rigs i have ever heard :)

Link to comment
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Go to SP mufflers and get the muffler of size you want and make a nice mid muffler. It's about that simple! I have 2x 3.5 Magnaflow straight through Mufflers and while it's pretty loud with the Varex open, it's quiet enough with the Varex closed. You can also buy off the shelf Magnaflow straight through mufflers as well. You also have a turbo to quiet the car down too. Don't overthink it. Buy my extra Magnaflow muffler sitting on a shelf doing nothing (buy it new, ignore this part)
    • Centre-offset muffler under the floor, same as stock. Just....3.5". The change from straight pipe there to centre-offset will mean that you need to remake some of the pipe (add a bend or two).
    • Hey guys. So my R34 GTT has a custom 3.5” exhaust (done by previous owner) with a high flowing cat, and then just a Varex cannon muffler on the back. The car does drone alot and is really loud even on highway driving just cruising, as you can imagine due to the Varex muffler basically being a straight through with the valve open. As much as i love a loud RB, it can be a bit much with no other muffling in line and just driving casually. I wanted to lower the volume output on the exhaust a bit, as well as remove the drone (probably a way to do both at once), and was going to do it all myself as I am a fabricator and have done exhaust work in the past, so the fab work isnt my issue, im just not sure on the right product or type of product to use to get the job done, and i doubt an exhaust shop would be wanting to help me as they wont be making any money from helping me, unless they supplied the product? Anyway any help or guidance in best way to approach this would be awesome   Thanks in advance
    • Meh, whilst the Honda is a "really" good car and has potential if you want to drop coin on, it was uninspiring for me to look at, but, it did serve its purpose and is now in the boys hands, his happy, his girl is happy, as she wasn't to keen on the noisy old Patrol, and most importantly, the Minister for War and Finances is extremely happy that her "little baby boy" (6'2 nugget who is currently training to be a copper, which will make 3 coppers in the immediate "circle of trust") has a well sorted reliable car that doesn't guzzle diesel Me, I'm more than happy with the NC MX5 that I replaced it with, it's a fun little car that I like looking at, like driving, and yes..... I do like the fact that the maintenance and modifications that I have done/will do are plentiful and relatively cheap, well........ while staying naturally aspirated slow that is, and that's all I really need for a fun little daily, I can rev the 5hit out of it rowing through the gears and never really break the speed limit  In saying that wicked word, "modifications", I've already ordered something for some noise and an additional "3 ish" horse powers, or whatever it gives, in the form of a header, and, a new set of "cheapo" BC coilovers that are already sitting in the shed waiting to get put in, I had the same BC's in my old NB and found they were fine for the street, hwy, and the occasional track days I did in it, they have 6kg front and 4kg rear springs which is about 10% stiffer than the stock springs which I found worked well for their price  I've also already been in touch with MX5 Mania in Dural, so once the header is on it will get a ECUTek RaceROM tune there (I cannot rev match for 5hit, and I loved the RaceROM rev match and FFS in my old 86 "RIP") In other, maintenance news, I put some new sparkler plugs in it, and have a new set of DBA Street series pads to put in over the next day or so, I'm running the DBA street series in the SS and Honda and really like them, they work great and are not dusty at all I've also booked in a few days leave over this weekend to give me 4 days weekend do some paint correction and give the leather seats some conditioning and interior some Bissell and steam cleaning OCD lovin', the carpet and interior looks clean, but from my experience with the Bissell IRT carpet, and the steam cleaner IRT trim, looks can be deceiving I've also found that finding a detachable hard top is proving problematic, the main reason why I didn't like the NC initially was the power retractable hard top that I seen them with gave the roof line a weird look, the detachable roof though looks good, and is a same shape as a NA/NB hard top, similar, but unfortunately not the same as it has different fixture point on the front, so fitting a easy to get NA/NB detachable hard top is no bueno New Old cars are fun, cleaning, hunting and playing around brings much joy How are your beasties going? Do you still have the Skyline with the LS???, or Barra??? that you were playing with
×
×
  • Create New...