Jump to content
SAU Community

Recommended Posts

Hey guys i got some problem with my car its drinking heaps of fuel i normally get around 350-450ish a tank depends on driving style but ever since the cold has came my car drinks a lot of fuel e.g i only get around 200k's a tank and my car hesitates to come on boost sometimes? like feels like somethings holding it back and also it misses around 5k ish only sometimes? i havne't done any modifications to the car

Mods:

PFC

PFC BCK

Turboback zorst

FMIC

Z32 AFM

Nismo 740cc injectors

walbro fuel pump

i havne't done any other mods since it was tuned wiht those mods....

Cheers

Chi

Link to comment
https://www.sau.com.au/forums/topic/275493-something-wrong-with-car/
Share on other sites

how long does it take for the car to come up to temp? it may be that your thermostat is on it's way out (or already gone) and causing it to run colder start enrichment for longer, or all the time. this will cause poor fuel economy, and the extra fuel can foul up the spark plugs.

also what do you class as a tank? how many litres? saying "a tank" is a useless measure as different gauges will read differently so you might be calling 30L a tank or 50L a tank. put your economy into L/100kms

It can miss on idle if the coilpacks are worn out... Higher RPM will often see coilpacks missfire in cars that idle normally simply because they are working allot harder as the RPM increases.

I'v had a coilpack gradually get worse and worse untill it was a WRX from the first turn of the key.

hmmm ever since i changed the radiator cap to an ARC one i've got a Koyo Radiator the max temperature it goes upto is 60-65 degrees.....normally warms up to 75-80 degrees with the stock radiator cap.....full tank is 50L or so :P

Cheers

Chi

that is very weird that the cap is altering the temp. never heard of that before. i know it can alter the boiling point, but never heard of it altering the running temp.

but i would still look at the thermostat. no matter what the radiator, etc, your temp will ultimately be set by the thermostat as that stops any coolant leaving the block until it's opening temp. so i would guess that it isn't sealing properly. that causes lower temps and longer warm up time, and higher fuel consumption

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...