Jump to content
SAU Community

Recommended Posts

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

i run the GReddy type s bov to atmo and its wound in to hard setting. It flutters up to three times if im just starting to build boost and back off (driving gently etc). Dont much know why how or what, but i do like the sound. For me the light flutter is ok, but the louder pchsshht is where its at when im up her. For that reason i stayed away from the HKS SSQ on the skyline.

Ive seen and heard a few vl's dosing and im of mixed opinion about it. one thing for sure it doesnt say hard tuned to me, it says hello ladies look at me im full sick....

All that said i chose the SSQ on my sigma to keep the noise down on gear changes. It's running short and large intake pipes so it's quite subtle but still doing the job. See how it sounds when i get to 18psi and if it's too invasive i'll go plumb back. With that car its all about less attention is better where skyline it's pose on.

R32 gtr 362RWKW no bov apexi filters and i can dose as good and loud as any VL and it sounds tough as like if it where in bathurst again, two turbos belching out sweet noise now thats where its at. And for those that say no BOV does damage thats bullshit 20k klms with -9 garretts and still perfect cond turbos.

cheers.

i love dose. i did an rb30 conversion and bought a vipec ecu so i could get rid of my AFM so i could get some better dose. ~$8000 later and i couldnt be happier. oh yeah, the car goes alright too.

Edited by SECURITY

thats confusing as shit.

Suction and dose?

Sound identical to me.

I've got one of them.. thats all i know...

Its sorta... suction... then... when i let go of accelerator... got the BOV and some of the suction letting out :S

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
×
×
  • Create New...