Jump to content
SAU Community

Recommended Posts

Hey guys just got a project going on just looking to see if people know where I can find parts listed below or who can sell them?

- R34 Z-Tune Side Skirts (Carbon Fibre)

- R33 Door Cards (Carbon Fibre)

- R34 Front Splitter (Carbon Fibre)

- R33 Duck Wing (Carbon Fibre)

- R33-34 Front Guards

Basically this is a 33 that will be having a 34 front conversion done thats why there's difference on parts...

Cheers in advance

Dan

Link to comment
https://www.sau.com.au/forums/topic/276406-carbon-fibre-parts/
Share on other sites

You know carbon fibre is illegal right(body panels etc).

You should probably think before you type such rubbish.

- R34 Z-Tune Side Skirts (Carbon Fibre) - NOT ILLEGAL

- R33 Door Cards (Carbon Fibre) - NOT ILLEGAL

- R34 Front Splitter (Carbon Fibre) - NOT ILLEGAL

- R33 Duck Wing (Carbon Fibre) - NOT ILLEGAL

The front guards might be an issue but are no more of an issue than people putting fibreglass gaurds on a skyline.

Edited by PM-R33
You should probably think before you type such rubbish.

- R34 Z-Tune Side Skirts (Carbon Fibre) - NOT ILLEGAL

- R33 Door Cards (Carbon Fibre) - NOT ILLEGAL

- R34 Front Splitter (Carbon Fibre) - NOT ILLEGAL

- R33 Duck Wing (Carbon Fibre) - NOT ILLEGAL

The front guards might be an issue but are no more of an issue than people putting fibreglass gaurds on a skyline.

Fare enough, my bad

Nuh the conversion guards would be fibre glass not c/f as the whole cars being resprayed quad layer white pearlescent to show off the c/f accessories :(

The main c/f parts cops harass u about is the bonnet when people dont secure then properly as they are lightweight and under pressure can come off and its happened to my mate

An aftermarket fibreglass/carbon fibre bonnet is mainly illegal because you are replacing a main crumble zone of the vehicle. Since your car was factory crash tested with it's factory bonnet, having an aftermarket brittle carbon/fibreglass bonnet on it changes everything in the event of a crash.

Manufacturers rather cars be crashed head on, hence why cars are usually built to understeer. You have a higher chance of surviving a crash front on as there is more of the cars body to absorb the impact and distribute the energy. Obviously there are a lot of exotic cars with carbon bonnets, however they have been crash tested with them and built accordingly.

Edited by PM-R33

Actually our cars have not been crash tested, skylines end up with engines in the drivers compartment on impact serious enough. Hence why they are not legal in the US (unless reinforced) We dont have a legal requirement for crash tests. Just recommendations

But its more to do with quality and shattering of the fibres and harming people and the fact they like to bring in laws.

Edited by DECIM8

We can supply you with the Carbon Duck Wing, will be back in stock in the coming weeks. They are $299 and available to purchase directly from our website: http://www.psiparts.com.au/detail.htm?ProductID=R33S-DWNG-CF

BTW: PM-R33, that has to be the first intelligent post about Carbon Bonnets I have seen in a long time. For some reason I keep seeing comments about carbon bonnets turning into ninja stars and killing people within a 100m radius of the crash site. :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...