Jump to content
SAU Community

Recommended Posts

As topic says I am a noob, so please no flamming :)

This morning car felt fine, this evening went out and when I put my foot down to accelerate there is no power when the turbo usually kicked in at 2500 rpm. I haven't done anything differnt than earlier in the day. The turbo gauge is going from -1 to 0 and no further. Had a quick look under the hood and couldn't see any leaks etc. Any idea's what could be going on?? Im thinking a trip the mechanic is in order.

Thank you for any advice

Link to comment
https://www.sau.com.au/forums/topic/276975-noob-with-turbo-problem/
Share on other sites

I concur with hyper gear, take of the dump pipe and look at the exhaust wheel

Im assuming this would have been the first thing you would have checked and as noone else has mentioned it have you checked all your cooler piping. When they blow off they can make a loud bang and then no power. Other than that it sounds like it icould be a turbo matter.

could also be a wastegate issue. if the wastegate is stuck open then that will dramatically affect performance. i had a boost controller once that would hold pressure between it and the wastegate so when you changed gears you would have no boost in the next gear.

so undo your wastegate actuator and see if it is moving freely.if it is, then also check you vaccum lines to make sure there are no blockages between the wastegate and the intercooler pipe.

then if that is still ok then pull off your dump pipe and check the exhaust wheel

could also be a wastegate issue. if the wastegate is stuck open then that will dramatically affect performance. i had a boost controller once that would hold pressure between it and the wastegate so when you changed gears you would have no boost in the next gear.

so undo your wastegate actuator and see if it is moving freely.if it is, then also check you vaccum lines to make sure there are no blockages between the wastegate and the intercooler pipe.

then if that is still ok then pull off your dump pipe and check the exhaust wheel

+1

Im assuming this would have been the first thing you would have checked and as noone else has mentioned it have you checked all your cooler piping. When they blow off they can make a loud bang and then no power. Other than that it sounds like it icould be a turbo matter.

Nope, it wouldn't be the cooler piping as the slightest leak in the cooler piping, and the car will not idle normally.

The fella mentioned it's idling normally....

Either the gate is stuck open, or the turbo is f'd

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
    • Wow. Pissy much? You on a mission to find old posts to argue with, or is this legitimately just because you're 5 years into a 1 day job?
×
×
  • Create New...