Jump to content
SAU Community

Recommended Posts

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

Edited by Chang
Link to comment
https://www.sau.com.au/forums/topic/277068-wrecking-complete-r34-sedan/
Share on other sites

Hey guys,

I've just purchased a complete R34 that i'm parting.

- Pair R34 Xenon's + loom for a R34 light conversion (inc. plugs / ballast / bulbs) $1500 AU

I'm located in Auckland, NZ so i'm only able to ship smaller parts. Anything to large to send won't be for sale here.

But PM me or reply here on any parts you want.

- Tiptronic

- RB25de

- 110000 km's

- Pearl White

71198351.th.jpg

72265125.th.jpg

Cheers :laugh:

INTERESTED IN XENON LIGHTS...STILL AVAILABLE?

Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

Edited by Chang

Here's a rough price list

Exterior:

Left / Right Non-Xenon headlights $1000

Left / Right wing mirrors $200

Monsoon / whether shields / wind deflectors $100

Rear wiper + motor + loom $100

Tail lights (tinted lenses) $160

Interior:

Airbag system (complete) Tiptronic steering wheel / Passenger airbag / Airbag computer $500

Air con unit (damaged face plate but still working fine) $60

A pillar trim + boost gauge (not branded) $80

B pillar trim (lower centre trim) $80

C pillar trim (rear where rear seat belt comes through) $80

Centre dash vent $80

Centre console (with leather lid / compartment) $120

Complete set (5x) seat belts inc. bolts and buckles $200

Door sill trims $80

Speedo cluster surround $60

Tiptronic shifter $100

Tiptronic shifter surround + ash tray $80

Tiptronic cluster, approx 110,000 km’s $150

Misc:

RB25de Neo ECU computer $100

Edited by Chang
Sorry Rance, Bonnet is too large to send via NZ to AUS.

lanky71, Xenon headlights are gone. But I still have a set of Non-Xenon's available.

666dan, yes it does have the cup holders. But going with the centre console.

But I have Pm'd the rest of you guys.

What if I supply you with the factory 'blank plate' that normally sits in that location? Then the centre console is still complete for you to sell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
    • All 3 I guess. The car came with the JASI Aero 4 door Type R Full Kit unpainted so this was one thing at the top of my list to complete then I noticed there were body panels parts for this kit so i picked them up along with some black mesh to fill in the front bumper and front side air vents. car is at a paint and body shop atm completing this work. Next I will be addressing the internal bells and whistles, great summer project I can do with the kids.  full interior removal - ,boys car sound deadening - pads and spray ,boys stereo, sound, lighting - Big 3, GTT or bigger alternator ,kids head lining - dye black add star lighting mod ,daughter. That's it for the next 5-6 months. I have some motor maintenance  work i have to plan out. oil filter relocation, gaskets, mounts. beyond that, mind is starting to turn over if i can use a DET intake plenum, block off turbo ports & pipe in a air intake.      
    • roller coaster of a ride. Alarm system was removed & main harness was repaired where possible. still no fix just random successful starts. moved on to the replacing the ignition switch and relay. well all this troubleshooting & repair has been going on, the car is at a paint and body shop being pushed around. Ive been going down there on odd days after work to get it sorted.     
    • 5th November if you want to come out for a spin wakfield
    • PROBLEM WAS BROKEN COOLANT SENSOR!!! Replaced with a new one and its running mint.
×
×
  • Create New...