Jump to content
SAU Community

Recommended Posts

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

i'll give you a week before that bar is ripped off

This is not a daily driver so will last longer than a week. I am more worried about the kerbs at the track or a spin to the infield. LOL

hey racegtst

thats the first time iv seen an r33 gtst with r32 indicators

I bought this bar as is and only painted it. Something different i say.

I think that i may end up selling this bar to get a GTR like bar that is not as low.

My drive is fairly steep but there was no scapring at all going into the garage forwards or backwards.

The coilovers will be coming out in the next few weeks and i will be going a king spring and bilstein setup which also raise the ride height of the car a little bit.

  • 3 weeks later...

Before (probably just a few days after I picked it up), parked next to my old car, which my sister drove until she got a Mazda3. Check out the SkylinesDownUnder sticker on the 'Rolla - I'm olde-schoole, baby! :thumbsup:

Theoldandthenew002.jpg

Taken by Wil at our SAU-NSW photoshoot day. This photoshoot was published in HPI magazine, and despite my car being the only Stagea there, it wasn't included... :) The car was digitally lowered and shot was cleaned up before being posted up by Wil - I love how good he's made it look considering how standard it still was!

CRW_2456_800web.jpg

Shitty camera-phone pic just after the old man and I had spent some time installing the Sydneykid kit (Whiteline/Bilstein package)

Slammed.jpg

Side shot:

Wagon001.jpg

Most recently, just after I put some V35 wheels on it.

NewWheels4.jpg

NewWheels2.jpg

NewWheels1.jpg

Mine when purchased

post-13913-1247906055_thumb.jpg

at the panel shop

post-13913-1247906146_thumb.jpg

Today after picking it up from the panel shop (still have to fit the number plate)

post-13913-1247906380_thumb.jpg post-13913-1247906518_thumb.jpg

I would just leave it parked at the panel beaters dude... with a front bar that low its gonna be back there in a day anyway

Nope sadly its the correct way.

After the crash insurance wrote it off, parts were just so dear.

Ummm I was cruising through a green light and BAM, lady turned in front of me. She didnt have a green arrow, but thought she could go anyway.

End of the 34 :D

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...