Jump to content
SAU Community

Finally Cracked A 1:16 At Op

LSX-438

By LSX-438,
in R35 GTR

 Share

Recommended Posts

LSX-438 Mentor

LSX-438

Posted
  • Author
Posted
So fast for std :) Which is a good thing as where the hell is the drama? Tyre screeching, oppo lock, wheelspin. windscreen wipers. I seem to recall a lot of that last time i was at OP and i was a few light years away from 1:16s :) ... :)

Sounds like me in my last car, arms and elbow flying! And that was for a 1:20.x

  • 1 month later...
LSX-438 Mentor

LSX-438

Posted
  • Author
Posted

Managed to improve by one or two tenths last Sunday for a 1:16.76, every tenth is getting harder...

Somewhat sloppy driving here, but hey, VDC may not have been turned on (but dont tell Nissan, ok?).....

LSX-438 Mentor

LSX-438

Posted
  • Author
Posted
good stuff I told you it's better with VDC accidentally disabled.... :)

thanks Richard.

Quick question: have you seen any R35's do Oran Park South?

I have a track day there soon, interested in a good benchmark time.

cheers

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah if you haven't been there before, and with your pace at EC and OP GP I'd say aim to break a 50. anything better will be gravy and after a couple of goes you should be down the 48s or so like dundan says. not that he'd know. he does 1:20 on the bloody nth circuit on his 50cc scooter...

LSX-438 Mentor

LSX-438

Posted
  • Author
Posted
yeah if you haven't been there before, and with your pace at EC and OP GP I'd say aim to break a 50. anything better will be gravy and after a couple of goes you should be down the 48s or so like dundan says. not that he'd know. he does 1:20 on the bloody nth circuit on his 50cc scooter...

certainly hope i do significantly better than a 50 or 49!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done.  
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      OK, so a bunch of trim needs to come off to get to the rear shock top mounts. Once the seat is out of the way, the plastic trim needs to come off. Remove 2 clips at the top then slide the trim towards the centre of the car to clear the lower clip Next you need to be able to lift the parcel shelf, which means you need to remove the mid dark trim around the door, and then the upper light trim above the parcel shelf. The mid trim has a clip in the middle to remove first, then lift the lowest trim off the top of the mid trim (unclips). At the top there is a hidden clip on the inner side to release first by pulling inwards, then the main clip releases by pulling the top towards the front of the car. The door seal comes off with the trim, just put them aside. The the lighter upper trim, this is easy to break to top clips so take it carefully. There is a hidden clip towards the bottom and another in the middle to release first by pulling inwards. Once they are out, there are 3 clips along the rear windscreen side of the panel that are hard to get under. This is what the rear of the panel looks like to assist:
    • GTSBoy
      R34 manual conversion speed signal wire finding, need help

      By GTSBoy · Posted

      Yes. Autos typically work from the speed sensor on the pinion shaft of the diff. I also think that even if you have a proper speed sensor for the bog manual in the manual box, that the signal it outputs is not compatible with the auto dash anyway. You should consult that manual (the book, not the gearbox).
×
×
  • Create New...