Jump to content
SAU Community

Recommended Posts

  • Replies 155
  • Created
  • Last Reply

Top Posters In This Topic

Wife and I will be at booval maccas to head down with the ippy ppl. Sorry Micah but this will have to be my confirmation. It's really hard to internet on my phone. But we won't be eating so don't count us in the BBQ numbers. C you all there. What chanel UHF are we using?

Wife and I will be at booval maccas to head down with the ippy ppl. Sorry Micah but this will have to be my confirmation. It's really hard to internet on my phone. But we won't be eating so don't count us in the BBQ numbers. C you all there. What chanel UHF are we using?

Hi

I think we used ch 16 last time. We can decide on a Chanel when we are at maccas

This should be good two black and two silver and I think I am the only s1 :whistling:

Phil

Hi

I think we used ch 16 last time. We can decide on a Chanel when we are at maccas

This should be good two black and two silver and I think I am the only s1 :ph34r:

Phil

don't count on it phil, if it all falls in to place i'll be lurking around there somewhere :)

ps micah's is a s1 to

Hey Rb26stagea, did you get my PM on confirmation of coming. Ill be there for suree!

Yeah, sorry: I got it, and a heap of others: put it this way: there will be plenty of food: I just needed a guide as to how much to get...

I am doing my bit to keep the rain gods away: apparently if you drink a lot of beer... :P

Damn, I hope my car is ready! tick-tock!!

Sounds like it will be a huge cruise. Unfortunately it looks like I won't be able to make it. MY Father in Law is visiting that weekend and we may also be camping down the Gold Coast. Have fun..

Allright Brissy boys i think Springwood Maccas is the place to meet.

http://maps.google.com/maps?hl=en&rls=...sa=N&tab=wl

(This is the one you guys were refering to yeh?)

I think probs meet round 7:00 to leave at about 7:15.

Then hopefully get to Coomera BP at 7:45 - 8:00 at the latest.

All in favor/All apposed.

This will be my first cruise also, looking forward to meeting everyone...... I'll meetup from Springwood.

Ok: I completed the final recce run today (in a Barina SRI: awesome! I was grinning the whole way: so much fun!), and am happy to say that the roadworks I had concerns about are all finished now! There is a section of minor roadworks for a couple of km right at the beginning of the drive, but nothing that will be of concern.

The remainder of the roads are great: good (relatively) smooth roads, a couple of decent rest stops and catchup points, some lovely countryside, and of course plenty of twisties: it's going to be a good run :D

Just bear in mind that it's a substantial drive, so bring along something to drink during the rest stops: we have a supply of soft drink etc at the endpoint.

Looking forward to seeing you guys and girls on Sunday!

Micah

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...